Short video of the first test of the new vacuum table
I built this vacuum table and heater mainly to make a large canopy for a project scratch built plane I was building, (plus I thought it might be handy for other things). I had to use 1mm PTEG (same stuff they make coke bottles/packaging etc out of) as no one in the country stocks .5mm so the result was not the best, (need to get it very hot) Heater box uses the guts of a 2 bar halogen heater in the bottom, plus a 500w halogen work lamp in the side (1500W total) but still needs to be hotter. Will try and do a build post later.
That was just a quick test, - did have about a 5mm spacer on it, but the one I did for the plane had about 30mm. Depends a lot on how thin the material is as well and you have to allow for trimming. .5 mm would have gone around a lot better. You also have to have holes through the plug as well so it pulls around the plug.
The CKD furniture company I worked for (largest in the South Pacific) pioneered round edge vinyl covered table tops in NZ using a big German press which they modified. Germans said the thin Vinyl that the company wanted to use would not work,- took them a year of experimenting and proved them wrong. Machine used a large silicone blanket and oil heated platen.
Probably one of the reasons Red, also they were apparently trying to compete in a saturated market after the war. They upgraded the motor a number of times (as you would have seen) and a few other mods but couldn't compete, - pity as it could have been a ripper little plane, better looking than a lot of others and faster.
As you said, tandem is not conducive to families, and a lot of companies were advertising their 4 seaters as an extension of the family car. Gone a bit the opposite these days, not many making small planes now, mainly the Chinese, (probably count them on 1 hand now) The Streak would probably fit in the sport plane class these days.
Just built Krick RO-Marin Neptun. First tug I’ve built, she came out okay, I think. 6volt system, MFA 2.5 geared motor, Graupner SXM switch controlling the lights, older Pixie brushed esc controlling water monitor pump. Old Futaba MC210 for motor esc, Frysky QX7 radio. This video was shot at Towne Lake, McKinney Texas. She well on her maiden, needs about 2-4 ounces ballast in the stern though.
The Lake Illawong Model Boats club and Task Force 72 Fleet Base Victoria had a combined display at the 2019 Sandown Train and Hobby Show. This video is compiled from the first 2 of the 3 days. We even had a pond erected, but unfortunately a few small leaks restricted its use.
Another youtube offering, and also Danish as per the last video. A very neat steam engine installation of a twin cylinder slide valve, in an open hardwood boat. The three figures on board are to a very high standard and dressed very much the same as the last video. it would seem besides bacon, Denmark is the place to find one's authentic boat crew.
Both this boat and the other one you link to is done by a member of Vallensbæk Modelskibs Klub, where I'm also a member Bernhard is the local king of detailing his boats (and trucks).
Hello Tica, and very nice to make your acquaintance, and I very much appreciate your comment. I think the two video clips posted are quite incredible, and very much admire the skills of the builders and the finely detailed finish on both boats. I rather wish we had more steam enthusiasts in this country, but I am afraid it is nearly all electric motors more is the pity. Regards to yourself and Bernhard definitely the king of fine detail. Gary.
Shadowing of U-181 from the subcam on HMS Triumph at the Naracoorte swimming lake. There are other videos and detail photos of these submarines previously posted on this site.
Trying to learn to use this forum properly I am publishing a video that shows an experiment I did to find out how fast the stepper motor could turn. I am using in my model of the sailboat Carina 2 stepper motors like the one shown in the video to work as a winch to control the position of the sails in a system solution where I am realizing this my own way to implement the sheets as shown on the original sailboat Endeavour. This requires my sheet control system to control the length of the sheet of the mainsail i.e. over a range of 8.3 meters. This requires the drum which is turned by the stepper motor to make 21 full turns. Details will be published in my report from scratch of building my Carina.
I found this hull at thingiverse last year. I printed the hull from a local shop and rest was handmade.
Firstly I bought a 2426 4200kv brushless 2-3s which was too powerful and too heavy for the boat size. The length is 38cm.
And the 30Amp esc was also too big for it's size.
After that I tried small 180 brushed motor with 20A brushed esc w/brake. it was perfect (still it's heavy😂).
The bridge and deck is made by 1.75mm pvc,torpedos are made of wooden pencil.
Small battery space takes a 2s 500mah lipo. 30mm 3blade propeller.
Excellent video Sakibian, well done👍
and you're very brave to sail such a tiny boat in waters like that 😲
Hat off Sir 😉
Cheers, Doug 😎
BTW: you should put this boat in your 'Harbour', just click on 'Boat Harbour' on the left of the Home page and then 'Add your model boat' at the top.
Happy that you liked the video , will try to post more videos.
And please don't call me sir haha? I'm still 23.
About the harbour , when I registered here I didn't find my country (Bangladesh), can you please do something while your an Admiral 😛
The CKD furniture company I worked for (largest in the South Pacific) pioneered round edge vinyl covered table tops in NZ using a big German press which they modified. Germans said the thin Vinyl that the company wanted to use would not work,- took them a year of experimenting and proved them wrong. Machine used a large silicone blanket and oil heated platen.
As you said, tandem is not conducive to families, and a lot of companies were advertising their 4 seaters as an extension of the family car. Gone a bit the opposite these days, not many making small planes now, mainly the Chinese, (probably count them on 1 hand now) The Streak would probably fit in the sport plane class these days.