TV Segment on the Suncoast Scale Model Boat Club (Florida, USA)
A few years back one of the TV stations in the Tampa Bay area sent a professional media crew out to record one of our meets. I got a copy of the finished video (permission granted by the TV station for reproducing). It is quite uplifting and shows you what model boating in Florida looks like.
I hope you enjoy it!
Lew
Florida 😎, USA❤️
A bit more video of a friend sailing my boat for the first time in VERY light air while I took a bit of film. A few initial teething problems with the running rigging ended this session but she does look and go well. This is a 60" J class from Alan Horne at jclasshulls.co.uk
The prototype J Class yachts were a class for the Americas Cup back in the 1930s. They were over canvassed and could only sail in less than 20 mph winds!
All of the original were metal hull yachts using the rising aircraft industry design teams for maximum strength against lightness of hull. In the case of the British Endeavour of 1934 she also had to be sailed across the Atlantic to get to the competition! If you look aft on the yacht there is a discrete black hole and this is where the mizzen mast was set for the journey.
The class had a formula which traded off hull length against sail area plus some stuff in between. A couple of hulls have recently been built one of laminated wood but otherwise those 'rescued' have had to be re-fitted to modern standards.
The Endeavour now has an engine with prop in the cut out rudder area and floats a foot lower on the waterline.
One of my yachts is the 1 : 35 scale Amati Endeavour kit modified to take to the water and I found the quadrilateral jib makes her look really good on the water. But as I say there is so much sail are that even at this size there is too much. I set her up to run with local expected breezes without the quad sail and she goes well. When there is a light breeze the quad can go on and I use the rudder to give some weather helm so she is under control.
It can be seen from the hull design that the rudder is sloped away at an acute angle and this can be a problem! Consider the hull heeled over 20 degress and you will see the rudder no longer operates in a directional way but just makes the aft of the yacht rise up and down, so you have lost control!
Therefore the yacht needs to be operated close to the vertical position. The extreme of this is the modern planing cup yachts which only work upright with a mainsail angle of just a few degrees.
I have added the 3rd. photo as it shows the detail of the mast. On the model this is a 'stressed' ally extrusion mast. The cross-trees are scale and the wire shrouds do strengthen the mast. The mast and sails are stored separately in a sail box.
When on static display I have a crew, nice and easy at this scale! There was a class system among the crew, the floppy (Rupert the bear) white hats are the crew the proper seamans caps are the officers. When at sea there were 22 crew on board I have about 9 on show. Ca'nt afford any more.
Having modified the connection to Jaws, the shark stays central to the stern. Whereas before he would veer to one side and tangle the connection around his fins. The steering of Orca is very slow as the shark tail fin has a lot of influence, in as much as wanting to remain straight ahead. The Orca has a large turning circle because of this, I would estimate a least 10 metres. Where as without the shark in tow the Orca turns in 2 metres. Something to remedy in the future. Here is a short video,
As far as I know, there is not a model boat club at Madrid. However, modellers gather Sundays at 10:30 to sail at a pond -actually a set of four connected ponds-, located in a municipal park, in the south of the city. Access is free.
The boat in the video is a sidewheeler, scratch built by my good friend Eduardo Yraola, who is a far more accomplished modeller than I am. She has steam propulsion, and sails at a majestuous pace.
The "Spooky" Halloween night sail took place on Sunday 29th October 2023.
Sorry for the poor video quality. Conditions were difficult in the "pitch dark " however, just for fun - it`s nice to have a record of the event than non at all. Commodore Barry says thanks to all who took part !.
Just taken dads old boat out and it handles well. I might add some short chines to the aft section just to stop it skidding out so much on turns and it is a bit over powered. Only running on 4 S in the video, 6 S next 😂. Not sure if the YouTube link works.
Believed to be from Revell Models , " INGA IV " is a model Ketch , owned and sailed here by Martin Ward of the Hayling Island Model Boat Club.
RCSailing is just for fun, no gain. Other than sharing photos and videos relating to Buxton Model Boat Club activities, from time to time its nice to "showcase" models from other clubs and members as seen here with the link between BMBC & HIMBC - all sharing the common interest in model boats and the "Model Boat Website".
Great weather this week so off to Leander Boat dock for Andrea Gail maiden run I made a video but could not down load on this wed site But I did take a still photo so here she is & the model work well .As soon as the boat pool opens a Spencer's in Burlington It will get a summer of running .
Hi Garth, boat looks good👍 Re the video, you may have to upload it to You Tube, then put the link in your next post,- video might be too big to post directly.
Philuk👍