Just finishing up a Chesapeake Bay "flattie" skiff. The bottom flat and is cross planked Here is the video fo the build

More work on the little boat today #lockdownfun

Finally got a good day, so raced down to the pond and threw the boat in. 2 problems, 1: battery had run down a bit with all the testing, and the new 18kg digital servo winch needed every bit of 4.8v, so functioned intermittently, meaning not much sail control, 2: jib boom needs a kicking strap to stop it 'skying' and tangling (knew it would happen but wasn't a worry). Apart from that, everything worked perfectly ( cheapo China Futaba knock -off rudder servo still worked fine on the low battery which is a bonus)

Sailed brilliantly like it did over 40 yrs ago, and as it's set will sail hands off on a reach, being nicely balanced, (even with the crappy jib,- which I had to make,- well actually my mother made for me,- back in 1980 after the original was stolen by a kid at the beach, while my back was turned😠) Funnily enough it was made on the same Bernina I used to sew (horrendously) the jib foot after trimming it for the boom a few days ago.

A few more things to improve and add, but pleased to have it back on the water. Another crap video, -seems to get blurry once it's been through the movie editor and You tube ) One day santa might bring me a Gopro, ("yeah right"!)

I tried to put this up in the How To Articles...but it does not have url upload capability. So here it is. This is a very good video on how to work with fiberglass with odourless resin. It is very simple and should make those who are nervous about this process feel very confident.

RC Stern Trawler - "Majestic" by Thunder Tiger. Model owned by Buxton Model Boat Club member Adrien.

For more photos, highlight and click the following link :-

https://model-boats.com/places/60518

Just for fun ! (I did this for the local school kids where I was caretaker about 6 years ago).
Best wishes to all !!⛄

Going fishing - through the Dire Straits with Mark & David . - Just for fun !.
Christmas greetings to all !

For more photos follow link :-

https://model-boats.com/places/60518

Just a couple of Submarines - from BMBC local Buxton Model Boat Club Submarine enthusiasts.

DONT FORGET - More photos can be viewed on the link for " BOATS CLUBS & LAKES "

( Highlight the link, then Right click go to > )

https://model-boats.com/places/60518

Second test was slightly better, using the aluminium spiral cut universal which came with the jet unit. As you can probably hear, it was horribly out of balance (even with cable ties to reduce it). It was not even drilled centrally and the spiral is right hand when it should be left hand, (like a spring twisted against the wind, it wants to deform). Slight improvement in speed on the first test (no slip this time) but the noise was horrendous.

Have pulled the jet apart and found that the 3 blade prop is around 1 mm too small for the hole, causing cavitation (see loads of bubbles in the jet stream) which is causing loss of thrust. The prop is the wrong type as well, with rounded blades, so I have modified a larger prop with more pitch to fit snugly in the unit to hopefully increase thrust. The shaft is also wrong, with a flat cut almost half the diam and carrying on through the bearing, allowing the grease to fly out.

I actually saw a Chinese site on Al Expr stating that "some dimensions on the product may be different due to the number of machines and operators involved in its' manufacture," SERIOUSLY!!??? their quality control must be utter crap and the operators not skilled enough to eat their lunch😐 Why bother having a dimension at all?? Little wonder nothing fits properly.

Unfortunately, most model shops sell the very same stuff, unless you want to shell out muchos dolleros for European stuff. I have just ordered some 4mm silver steel to make a new shaft, so a coupling or silicone tube will fit better. Also ordered some solid connectors to try. Vibration is wasted energy so it needs to be eliminated. Hopefully the mods will improve things and allow the motor to run on 4s rater than 3s. Worked out that the motor is only 1200KV, so it's only doing around 13,000 rpm under load. Probably will need around
18,000 rpm for proper performance. Onwards and upwards (or forwards as the case may be.😁)

Sorry about the blurry vid again, but my camera lens is knackered.

Weather was perfect tonight for a test, so I did the 15km trip out to the Gulf harbour pond (most weed free pond) to throw the boat in. After a thorough under water hull inspection from the marine department, she was off. Everything worked ok except the silicone drive tube which had become enlarged due to soaking in the grease coming out the front of the jet shaft. It was slipping badly and probably losing about 60% of its' thrust. Manoeuvrability is excellent but reverse leaves a bit to be be desired. Steering in reverse is perfect but the thrust is not going forwards enough from the bucket. Might have to build in some nozzles to direct it better.

Smoke air and water are working as well as can be expected, (smoke is a bit wafty, but with too much air introduced it will disappear as it gets thinned out too much to see) I was not expecting miracles as this was a bit of an experiment (modified cheap jet unit with unknown abilities) but at least it shows promise😁. If I can find a coupling which is concentric it will solve the drive problem.

Trouble is, the Chinese insist on making a 4mm shaft, 4.95 (or whatever) which is useless for balance in a 4mm ID bearing for example. Fine for cars, but no good for boats or planes due to balance requirements (it's a mission trying to balance plane props due to this thinking,- they do it with everything) shafts for electric motors are a nightmare at times as the play they build in, can ruin an otherwise good motor. I might have to buy a flexible rubber/nylon universal or a collet style( preferable as these take up any undersize on shafts) to fix it. They included a spiral alloy one with the jet unit which is as loose as a rooster in a sock, and only good for slower things like 3D printers etc. One of these days they will learn how to machine things to fit.😐

Smoke air and water switching sequence, (sound's out of sync for some reason,)

A bit more refinement on the timing but getting there. Finally got the voltage regs from China to complete the system. A bit noisy, as the water pump is dry,- quietens down with water. Switches in stages using Grahams magic timer, - 1. smoke on, 2. water and air on. There is actually smoke running constantly at a reduced level once everything is running, but very hard to film. I could turn it up but I don't want it to look like it's on fire😂