Search
867 posts for “hull paint” · in Blogs
Page 20 of 31
Blog
VINTAGE RUNABOUT
… ill sit flat on them. Shafts will be epoxied in later, once hull is glassed and oiler tubes soldered on. Seat and its' back cover is removable to enable shaft tubes to be inserted from the front through the motor mounts. The rudders have be …
Blog
Shannon class lifeboat The morell. (99% completed)
… through the Speedline 1/12 kit. I’m presently finishing the painting of the hull. All work above the fenders is done. Not an easy build but a good model is achievable. The kit.
Blog
Bit more progress
… ng strake, I was pleased with how that come out. Up next is painting the hull, adding the fittings, then onto fitting a motor and so on
Blog
Sea Queen Restoration
… shots of the internals now. Hoping to get back sanding the hull tomorrow. Wife’s had me painting the Garage today
Blog
Deck in place
The hull is now painted, which is a big step forward. The anchor holes have had pieces of styrene tubing glued to the inside of the hull, and then 2 part epoxy resin wrapped around them. This should stop any water ingress, and will look goo …
Blog
Back half of the focsle deck
The hull is getting painted at the moment so I decidedly that the deck which goes under the splinter deck could be started. Unlike the Pontus photo etch which gets you to completely remove lockers, the mk1 design kit only requires the tops …
Blog
Fin and Keel
… ighing 4.5kgs. With all the extra details I've added to the hull it has turned out heavier than the design weight (No surprise there then ) so to keep the total weight of the model on target, the keel weight needed to be reduced to 4kgs. To …
Blog
Bit more done
Hi y’all. I spent this week trimming the hull/deck flange, started with a Dremel then finished with 80 grit sandpaper. This will be covered by a large rubber rubbing strip so it doesn’t have to look perfect, but it was too wide hence the tr …
Blog
39' Windboats Fairwind. Decks, cabin sides, companionway steps.
… lind, 1940 Thames cruiser. Cabin sides and steps done, deck painted. The hull always gave a clue, but the emerging profile and shape of the windows clearly date her. She's a lovely old classic Thames and Norfolk Broads motor yacht! The cabi …
Blog
More Sanding 🤯
Done a bit more sanding and repaired the hole in the hull. Ive also test painted inside one of the bulkhead sections. I’m going to spray the hull this week in primer and see how it comes out and I’m thinking of having a go a planking the hu …
Blog
She floats!!!
… d from Battlecraft and they really look the thing - had fun painting them and completing the engine hatch which they'll be attached to. Did a rough positioning of the gizzards (I bottled making the engine mount and ordered one on fleabay bu …
Blog
Once again the devils in the detail...
… ours of masking all the areas not getting a coat of texture paint, the textured paint was applied with 2 light coats. once fully hardened overnight, the masking tape was removed before giving the whole deck another coat of primer to seal th …
Blog
HAKITS- PILOT LAUNCH-LARGER VERSION.
… dows were easily fitted to the cabin sides after any excess paint had been removed from the inside edges of the aperture. No one said that fitting the rubber surround to the deck would be easy, and my first idea was to use contact adhesive, …
Blog
Thornycroft Update
So I've got the hull all done, cut the apertures for the portholes and got the foredeck down. I can't really do any more until I have the gizzards. So ignoring the things that will actually make this vessel GO, I've concentrated on the fluf …
Blog
Dumas Higgins PT boat
… stmas present, a Dumas Higgins PT boat. This kit has an abs hull, a plastic deck, vac formed cabin, and numerous wood and metal fittings. Like most Dumas kits it does NOT come with running gear, nor shaft tube or rudder. However, I have tho …
Blog
And Even More Planking
… would have hoped, so to cheer me up a bit I have started to paint the hull. And no more floating twigs in the kitchen sink, as my wife describes my careful soaking of the planks!
Blog
Maid Rosalind, the 1940 Thames cruiser
… s cruiser. Applied three layers of West System epoxy to the hull, clear on the topsides where the planks have to show through, but plus fine fiberglass cloth below the waterline. Initial sanding was with a Fein sander and 40 grit paper (yes …
Blog
HAKITS- PILOT LAUNCH-LARGER VERSION.
… ilar joining piece will be in place at the join at the bow. Painting of the hull is still progressing. Soon will be able to get the radio get into place as the next job. Geoff.
Blog
HAKITS- PILOT LAUNCH-LARGER VERSION.
… itted from end to end and pushed over the side of the mesh. Painting yet to be finished. I have used a similar piece of this mesh to cover and opening in the forward hatch under which will be a small electric fan. The exhaust will be taken …
Blog
S38 Schnellboot by Italeri 1/35 Scale
… RC tx and rx, many LEDS, electrical components and a ton of paints (italeri to other makes has been done where possible). I'll need to buy 10 cheap simple servos at about £17.00 and 4 good quality servos at about £50.00. My ESC will need up …
Blog
Timberheads
… cuppers were cut through the gunwales on either side of the hull, level with the deck to drain any water that comes over the sides when the boat is heeled over. Four fairleads (two either side) were added to the gunwales for rigging cords t …
Blog
HAKITS- PILOT LAUNCH-LARGER VERSION.
Completing the Hull structure and Sundry. It has been one of those periods where building a model seems to not be making much progress despite spending the usual amount of time on it and then suddenly another major step has been completed. …
Blog
Mounting the Winch servos
Having sealed the inside of the hull with two part epoxy, it was given a couple of coats of white Hammerite to ensure that there will be no water damage, and to make it easier to see inside the hull once the deck is fitted. There are two wi …
Blog
Phantom Tug
… update this time. The timberheads are all in, the bulwarks painted, deck laid and sealed, so it's on to the cap rails. There was no way to bend a flat piece of wood sideways to the curve of the hull, and knowing these would be painted, I o …
Blog
Sealing inside
… een filling and sanding set up two part finishing epoxy and painted on to the inside of the hull. A good coat went on and will need to set up. touch ups may be need for some areas . Rick
Blog
Steam tug Lyttelton
… , saves.....trauma? Anyway, we're up and running again. The hull is now painted and lacquered. The name lettering is laser cut vinyl lettering, courtesy of the Leeds Model Shop, whose mail order service is a life line at the moment. The rea …
Blog
Ink bled
… e after coaming is done and everything fibreglassed, I will paint the deck to match the hull, or a contrasting colour.
Blog
Water line
… st so decided to use it to put a line around the top of the hull to give a nice distinction between the blue and walnut woodwork. Just a point, the trim line was probably 20 + years old but still as good as new. I also applied the rear fend …