Just thought I'd show you guys my boat with the "too fast" brushless setup. I have now put a smaller motor and turned it down on the controller. Almost lost it though 😁

This slide show shows the build and final result of my scratch built Seaplane Tender. it is 1/12th scale and powered by 2 x 250 watt brushless motors. Built in 2011, it sails at Knightcote in Warwickshire and Tynemouth in the NE.

This is a Deans Marine Kit which I built about 2 years ago. it is now fitted with a 180 watt 1100kv brushless motor running on 7.2 volts and using a Turnegy 18amp car brushless ESP. With a 35mm X type prop it FLIES.

Here is my scratch built Seaplane Tender in !/12 th scale. it is powered by 2 x 250 watt brushless motors running on 7.2 volt Nmih batteries. Pictured here at Knightcote Model Boat Club in Warwickshire and a couple during construction.

This is my 46 inch fireboat. it is a 1960s Aerokits model that I was given about 18 months ago only partly started (frames and stringers). it is powered by 2 x 770 watt brushless motors with 4s lips and has working monitors and an Action Noisy Thing sound system. it is pictured here at Tynemouth boating lake where I an a member to of the Tmbc.

this is my boat built from the aerokits plans. she is the 46 inch version, power is from a brushless motor and lipo set up. sailing trials over easter hols weather permitting!

The police hovercraft is from a Griffin 600 kit by Palaform Limited. 600mm long, hence the name. it is run on a single brushless motor for both lift and thrust. it is built from depron so is very light. I use 11.1v Li-Po to save weight. Great on land too, in fact very fast on tarmac. Fantastic fun.

HI to all you Fire Boaters,
I have decided to finally bring my Fireboat out of the closet and up for inspection.
This is the first of my many boats I am showing, I will probably show others in the future.
I started to build her back in 2006 after being off work and having a shoulder operation. She was not going to be a R/C boat, just a bit of something to do whilst on recovery.

I have a 34" still in the box unmade, purchased back in 1994 from Aerokits.
I drew round all the parts and then shrunk them on my scanner. She is 27" long I think that's
just fraction over 1/20th scale . She is almost all balsa except the 2 under skins that are balsa laminated with 1/64th ply. The hand rails are 1/4" balsa blocks I cut from a strip and the rail is ally tubing.
The mast is made from plastic strip from packets from the model shop.

When I returned to work she was put into the shed and left unfinished.
I stumbled across the Fireboat website and registered in 2009 when I was off work once again. This then made me think more about working on her again and I decide to turn her into an R/C model. So out she came and I fitted an Electomax Delta 480bb motor and a M3sonik esc.
I also purchased a couple of Robbe fire monitors, put them together shortening the nozzles and cutting the bottom of the base of to try to look a bit moreto scale. I know they are not the correct type but if I want to go down the road of getting them working then these ones will.

Then off I went to Wilkinson's and bought some paint. Then set out to paint her, as I brushed on the paint it seemed to be drying almost as quick as I was painting her. Dragging the paint I had just put on with next brush stroke. What a TOTAL DISASTER !!. I gave up on her and back into the shed she went.

2010 arrived I started again rubbed the paint down a bit and bought some Tamiya spray acrylic and started spraying, underside red, it seemed look all right. I used a nice new roll of low tack masking tape, taped up the underside and the decking and sprayed on the black on the sides. I thought that look all right. Took off the masking tape, which also took off the red paint and the dope from the decks. Another DISASTER. Back in the shed she went once again.

A couple of months went by and I was up in Norfolk on my own boat and watching the workers in the boatyard, ideas came to me and when we returned home, out she came and I repainted the sides
and then with red oxide paint I painted her undersides to make it look like antI foul paint. I used some white stripe to cover the join of the two different paint colours.
I had bought some roundels in Anglia Model Shop in Gorleston and some lettering in a shop in Norwich and after painting put these on.
Not looking fantastic but passable I was a little happier with her, but still not satisfied, back in the shed she went again.

Now after so much nagging from my brother out she has come, I've started again. He talked me into changing and trying a brushless motor and a smaller esc he had in his tool box from his helicopter he was shelving as its rota head was damaged beyond repair.
I have now fitted them and if they work I will change the esc to a forward/ reverse esc in the future at some point.

Sea trials are still away off more than likely in the spring, because the decking has yet to be painted. That will be the next job.

I think that's all for now, as I have probably bored you all to tears. I hope update as I progress further.
Just to let you know I'm Tom (alias BOATSHED).

Aerokit Fireboat 34"
Boat was given to me in poor condition approx 30 years ago, no running gear and most fittings missing or broken, originally powered with IC motor.
I have installed a 43A 700KV Outrunner Brushless motor, Model No : XYH42-50 and a Hobbywing Seaking 60W / Reverse Program Brushless ESC bought from Giantcod, powered by a 3 cell 2200 mAh Lipo battery runtime 15 to 18min, the prop is a 42.5mm 2 blade racing prop. I am well pleased with the performance of the boat.
I belong and sail at the Hartsholme Electric Model Boat Club, Lincoln.

Scratch built from My Hobbystore plans and Model Boat magazine, brushless motors running on 2x7.2 volt 3700 mAh batteries

Areokits 46" Fireboat with Brushless motor running on 19 volts Nimh batteries

My restored Aerokits Sea Queen with Brushless motor at Fleetwood on a very windy day