In case you have a smoke device using these or any smoker you can fill remotely by this method. Just used a reservoir and (for the purpose of the test) a 6v water pump running as slowly as possible. Pump sucks fluid through the smoke tank from the reservoir and recirculates it back to same. Reservoir fluid level needs to be level with, or below the smoke tank inlets to avoid siphoning to the tank and flooding the wick. With this system it only takes a few seconds to fill. You could also use the same idea manually with a deck filler and overflow. Either system must be sealed (airtight) to avoid fluid draining from tank when not in use, ( Manual system - both tubes plugged after filling) This idea does away with disassembling E-pen to fill .
JB

Think I've finally sorted the mixing smoke and water for exhausts problem. Graham has already done his using the same pen / e-cig unit but with some nice electronic controls for the on off system, but not having the electronic abilities I've just gone with a more basic method. Wired up the pen and installed a filler tube (2 tubes are better - one for a breather) these are capped after filling to prevent air getting back from the pump. This system has a water pump, an air pump and the smoke unit, (all adjustable with their own voltage buck) Thanks to Martin for his pen suggestion. I was previously using large capacity elements fitted in various containers for my experiments (truckloads of smoke available) but these pens are great for tight spaces and don't draw much current.

Air, and a small amount of the cooling water are mixed by venturis just short of the exits (the air pushing the smoke and blowing the water clear of the smoke tubes). I've fitted the same system into my ST but am still waiting for the air pump from China (postal system problem there, then Chinese new year holidays with new rules apparently) Get the odd bubble at rest but with the low exhaust you can't have everything.
Latest vid with boat in the tank.

JB

Using the e-cig element in the alloy box again but with the old smoker pump bored out and converted to a single outlet in line with the piston. Even makes a cool sound out the exhaust side!. Still waiting for my air pumps so just playing around in the mean time. Also trying glycerin and water 50/50 instead of baby oil. The pump doesn't shift much air ( slightly more blowing than sucking, - sort of pulsing back and forward) but if I blow down a tube I get clouds of smoke, I'll see what the air pumps do. Still only running on 2v.
JB

This version of a smoker box uses an E-Cig element in an alloy electronics enclosure.I gave the lid and box a 7mm haircut on the mill to reduce the size, (now 50x50x26, - was 50x50x33) but it could still be 1/2 the width. haven't found a smaller alloy box yet but might come across one, (only really needs to be 35mmx35mmx25mm The element is mounted on a bracket screwed to the bottom of the box (the box being the resevoir and neg) and against the outlet tube, and the pos wire runs through the side (in silicone tube) to the element.

The box is packed with cotton wool which is surrounding the element and soaked in smoke fluid (in this case baby oil) but leaving a passage through the center for air flow. I'm waiting for a couple of air pumps to arrive but I've used the old smoker unit pump again to demo the smoke and pulsing, (makes good smoke rings too)😊

The element is capable of taking 4.5v, but I'm only using 2v for the test and it smokes quite well. The pump is running on 7v but can be varied from around 3v - 8v. The large tubes are to allow for later exhaust fitting (water or dry stack). Once I get the air pumps I'll be running this one with the water again. I've done this (like Grahams version to be able to easily replace the element as the Heng Long smokers, while working ok (but noisy) have non replaceable elements, so if you kill one, it's off to file 13 at the end of the bench😉😁

The pump actually works quite well and if you mount it on sponge rubber it is reasonably quiet and could still be useful in a boat with a bit of interior room.

Inspired by jbkiwi's experiments on a smoker, and interested in developing one for my Crash Tender I have built an experimental rig based on using an e-cig for the smoke generator and an air pump. The air pump is driven by an electronic lash-up which pulses the pump at a rate depending on the throttle setting. The video shows two tests, first with the water off, then with it on.