I need to stay off the internet, LOL
Noticed an ad for an Estate Sale. I went, I looked, and found (i.e. bought).
The Midwest Rowing Dinghy, Canadian Canoe, and Chesapeake Double Kayak are all nice boats.
They will look nice in a Diarama or just on display in my Home Office or Family Room.
I plan to do some work on the Cranberry Isle Lobster Yacht. It was not built/finished to run.
I'd like to open it up and put running gear and electronics in it to make it a working RC.
The front opens to access where the motor and electronics would go, but the rear is sealed tight with no access to attach a servo to the rudder.
Does anybody know where I could download the plans/instructions for this boat? I would like to see how the rear is constructed before attacking it.
Thanks for the help!
Dave B

Bow all shaped wooden hull and upper structure is sealed. Hull has been covered with glass fibre. Ready for sanding and primer.

Hello again, here’s a picture of an M class destroyer which I built some years ago, she is of again balsa construction from Model Boat Magazine plans, I built over one winter about 9 years ago, she is sealed with dope and tissue which gives a smooth finish, the guns were constructed from plastic card, with brass rods for the barrels!
She was retired a couple of years ago, but recently she was brought out retirement and gifted to family friend was showing an interest in battle ships!

Here is pitcure of both my boats sailing on a boating lake not far from my home, the larger of the two was commandeered by my 8 year old son for a trainning mission he had in mind, which gave me an excuse to build another one, which is the smaller boat the picture, as the young captain needed escorting while getting use to his new command!
They are both made from balsa wood, which the material for the hull, it is sealed with a acrylic varnish,painted over the top with enammel paint with clear varnish on top of the paint! The superstructure on the larger destoyer is made from thin plywood, and on the smaller frigate its made of plasticard!
I got the lynx helicoptors on Ebay from "The Dorest Print Man" I think it was, which are 3D printed by him!

I have taken the old wooden hatch cover off to find out what was inside there was something that moved around when you tilted the boat found the end of a hand made brass anchor and the remains of some sort of leaf or plant the joints are sealed with tar the inside has been carved out i find it very strange that the two items were sealed up inside i think it is very old possible the 1900

Ex Display Model - Gaff Rigged Bristol Pilot Cutter :-
After sorting out initial problems of a "leaky" hull with extra sealing inside and out. Attention was then drawn to adding an extended keel by subsequently casting a lead weight for the base of the keel fin, then checking required depth for balance and trim .

My Gaff Rigged Bristol Pilot Cutter started life as a static display model which I recently adapted for " Radio Control " . With extra sealing inside and out, she is seen here on her inaugural trial sailing - checking balance / trim /steering and simple sail control.

Certainly no claims here on scale or workmanship ! - just a " fun and functional " model which more than satisfies my initial challenge ! . ⛵

I've replaced the old 6v sealed wet battery with a lipo 3s,11.1 volt 2200mhz, 100c spectrum smart battery. so the 1st run was cautious i just fired up the centre prop to see how she performed, well i was surprised at the turn of speed she had on just 1 prop, and how well she planed, it was a little awkward filming and controlling the boat by myself as i was the only one pond side. this was not without mishaps though, see 2nd video
After checking the boat over she was found to be unmarked and no bits missing, not bad to say she hit the pontoon at full speed, took off and plunged back in at the other side.
So the second run i started on the centre prop and then opened her up on the outer 2, she shot forward and immediately stalled, dead in the water. luckily i could reach her with the ponds barge pole to pull her to the side. i found the fuse had blown , i had fitted a 20amp mini flat fuse, i didn't have a 30amp only another 20amp which blew just as quick, upon opening up the outer props.
any ideas anyone or will a 30amp do the job, or a 2s battery? help any suggestions considered.
Roger

Not something you see every day! Saw a 'Sealegs' boat coming in from over the horizon and it eventually came straight onto and up the beach past the Orewa surf club. It then proceeded about 300m down the main road (holding up the traffic) to the petrol station to fill up, then went back and down the beach, into the water and away. Guy broke a number of rules doing this but looked like one of those 'don't give a stuff' people, His wife and tiny kid (the only one with a life jacket) were sitting in the back all the time.

The Sealegs is an NZ designed and built (built in Albany- Auckland) boat sold (and copied) all round the world. Really amazing piece of kit. Drive is hydraulic, and driven by a small self start diesel motor in its' own compartment. If I ever won Lotto I'd certainly be looking at one😁 They have a special drive on trailer as well.

Not my lake in the thumbnail, don't know where that came from😐

Sealegs leaving the beach (vid 2)

Video shot last week in our latest sailing venue, Hamilton Harbour, Ontario

Video taken of the model under way