Search
1,259 posts for “hull paint”
Page 41 of 45
Blog
fairey huntsman 31
… water. i got bored with the colour so i rubbed her down and painted the side of the cabin a dark blue which acutlly was the same colour as my car and the tops of the cabins and hull white, i re-covered the seat cushions with red leather and …
Blog
San Pedro Push Boat
… edro needed it's waterline so I put one, especially since I painted the hull brown. So I put the waterline because she just didn't look right with out one!
Media
Admiral Barge
… n pic 1 that's the condition she was in when i got her .The hull was in perfect condition under the paint work I replace the back deck and the deck in the middle where 2.5cc diesel engine goes in and now its all electric .in pic 2 is the fi …
Blog
San Pedro Push Boat
Having started painting the hull the deck and push pads, I've discovered a breach in the hull that's about 130cm X about 1cm or so! I'm hoping when I reglue the seam it takes, I'm not sure what to expect next.
Forum
Aeronaut Pilot Boat
… scale speed is there or thereabouts. As you can see, I have painted the hull above and below the waterline and I am currently working on the deckhouse. You will see on the pic of the finished boat there is a black stripe just above the wate …
Media
Sea Queen
Bought as a wreck off ebay . stripped down,repaired hull and top sides. re positioned the propshaft. Re painted. New Brushless motor/ Lipos etc. Goes quite well for an old girl, Believed originally built in the 60's. Ill try to upload a vid …
Forum
Aeronaut Pilot Boat
Morning Ed Hull construction complete. Could have been better as you can see from the pics, but with Milliput, fine-grade paper and patience I should be able to get a pretty good finish for painting. it is my first attempt at a plastic hull …
Media
HMVS CERBERUS
… ustralia I was taken by the history of HMVS Cerberus, whose hull is now a breakwater in Port Philip Bay. After a lot of research on the internet I decided to build a model of it. it is not totally accurate as I could find no definitive plan …
Blog
Monster Mersey
… see it rot away so I decided to take it on.I am now on the hull,it's been rubbed down and ready for paint then I can put it on the carriage and start from deck upwards
Forum
For Sale 1/20 th "Empire" Tug.
… llast that has all been labelled, as to its position in the hull. I have put the switch's in one of the lifebelt lockers, so you don't have to keep lifting the superstructure every time to run it. I only started doing this hobby a couple of …
Blog
Tugboat Serenity
I've glued the Hull together and have also used Bondo to the Keel, having done that I also sanded it. Make sure the keel is sanded and leave a little grit on the surface for the primer and paint to stick to!
Blog
Hawser holes cut
… ed for anchor hawse's. Anchor not yet fixed as will need to paint hull
Forum
PCF (Patrol Craft Fast) SWIFT Boat Vietnam Era
… unners. You cannot buy something like this. The glass fibre hull is complemented for strength and lightness with plastic and ply wheelhouse and cabins etc. Lets get to the point, its £525. Might seem very expensive to some, but to others th …
Forum
Sea Queen
… ou wont have too much work. My Sea Queen needed all the old paint removing and renovation inside as an IC had been fitted. Needed to replace the shaft as the original was too badly worn. Took a while to remove all the old gunge inside but f …
Blog
H.M.S. BULLDOG / BEAGLE
Working through the many finishing touches to the hull, but it is essentially complete. Even got the first coats of paint on! The pre-paint preparation was quite quick as the hull moulding was well finished. Obtained the deck planking; this …
Forum
Aero kits sea commander
… sed with IC engines and the resultant fuel spillages in the hull can result in some delamination of the ply skins. it will take some time to remove all the stains and damaged bits but time spent now will save you much grief later. if an IC …
Harbour
(Naval Ship) Perkasa
… its not quite finished yet but only needs the bottom of its hull painted. I'm hoping for a maiden voyage some time mid 2017. (Motor: 540) (5/10)
Blog
H.M.S. BULLDOG / BEAGLE
… mplete with a correct section and shape. Rudders primed and painted. The rudder shaft tubes had previously been installed into a wooden block glued in the hull to provide a rigid mounting.
Blog
H.M.S BULLDOG / BEAGLE
… cutter. Epoxied the outer frame into holes drilled into the hull and filled any gaps up with epoxy. Have left the glasses out until the painting is complete. The cut acrylic rod surfaces do require polishing to remove the cutting marks. Aft …
Blog
Sea Queen
… own for the undercoat then the finishing coat final coat of paint to the Cabin & hull
Forum
Hants and Dorset HSL
… pretty good condition. Couple off scuffs down left side of hull that could do with painting but don't know how I'd match aged paint yet. Unless I decide to have ago at restoration. Only plans at the moment are to fit a rudder and admire it …
Forum
First Boat--First Project -- Sea Queen Restoration
… tom of boat. Repaired all holes and depression in bottom of hull. Got roofs to fit properly, in process of making new roof parts for fixed part of front cab. Fitted beading around edge of deck, made adjustable motor mount so hopefully when …
Blog
HMS Diamond D35 - Build update Twelve
I'm nearly ready to give the hull it's first coat of sea going paint. I'm pleased with the lines and shape. I must admit I have spent a little more time on this particular build than I have other projects for some reason and this is not a D …
Blog
Build Update
Hello all, Ok, so getting closer to the Hull being finished, I've painted the Antifoul and Water line, I've gone for an Olive Green Antifoul, it mentioned this on the plans and found a Revell colour that suited. I've also sealed the Foredec …
Blog
Bits and pieces
… resent. The larger installed bits have been fitted into the hull: the fire monitor pump, the SLA battery, the drive train, and the towhooks with release servo. Various deck fittings are being constructed and painted. The stand for the fire …
Harbour
(Yacht) "Kaapstad" (Cape Town, Afrikaans) registered In Durban.
… ept for the funnel,vents and bridge(tin plate). resined and painted hull. Sailes her last Thursday and it went well. Due to the weight she didn't bob about on the water. Time to sell and move on to my next project,probably a tug. (8/10)
Harbour
(Other) RAF Range Safety Launch
… Range Safty Launch two years ago and I am now changing the hull paintwork to also include a water line. I never got around to doing this for some reason. Range Saftey Launch I purchased the plans for this model after my late father passed …
Forum
My first cargo ship
… as a bit of a wreck on ebay,I stripped It down to the bare hull,and renewed the decking and superstructure,except for the bridge which Is metal.I know Its not prefect but It Is my first attempt at a complete restoration. It has working lig …