Finally got a good day to try the new brushless motor. Boat goes 100% better now (if a bit noisier) 3s 25c 2200mAh liPo got a bit too hot, so probably need to up the C rate to 40 to keep it cooler (maybe install a fan as it's closed under the seat) It's pushing a 6lb boat with a 26mm jet with a 3000kV brushless so it has an excuse to get hot, (only got down to 3.7V/cell after that run, so not too bad). Runs with a more scale look now which is what I wanted. Took a bit of experimenting, but got there in the end. Thermostatic cooling fans for the motor worked well, and within 10 mins the motor was cool. Only used around 2/3 throttle so as not to stress the coupling too much (you can hear it protest a few times, - silicone tube slips slightly making it squeal)- automatic rev limiter😁
Sorry, vid is blurry again ☹️ (original's fine -HD) but something happens when it goes through my movie editor then to YT. Keep procrastinating about getting a better camera (or maybe it's just the editor. - More experimenting, this is getting tedious😐
Hi Ron, haven't spent a huge amount due to the fact that all the electrical bits are very cheap ($1 ea for a voltage reg, $8-12 for a pump, $30 ea for a motor (bought 2 as the first was not fast enough) and jet unit, $15 for the ESC, a few JST plugs and wire, $3 smoke pen, few lengths of silicone tube etc, plus balsa and f/glass, -probably not a lot more than NZ $200. A lot of things you buy of course like resin and paint, usually have to be bought in bigger quantities than you would use on one model, and may be used on other projects, so it's hard to work out an exact cost. I think the hull was the most expensive part, due to the cost of balsa and resin.
Mostly a lot of time, (hate to work out the labour cost on any model at going rates,- probably in the thousands)!
Set the new Surpass 3000KV 36 diam finned in-runner up in the boat, and did a tank test. Lots more power than the HV brushed 1200kv 550, but with higher idle. Re-did the reinforced silicone coupling and fitted a small collar to the inner end of the motor shaft to hold the tube from moving forward against the motor, as with the extra torque of the in-runner, it was trying to twist the tube off the shafts. Seems to be hanging in there static which is a promising sign. Once running, the load will come off which should help.
Runs full at around 4A and the battery holds at around 3.8v/ cell )alarm is set at 3.6 for safety, (as a sort of rev limiter) performance should improve a bit now. Have to wait till tomorrow as the restrictions end at 6am Sunday, (then have to hope for good weather for the test) The prop in the jet is a 28mm 3 blade racing prop which I modified to fit. Don't think I'm going to get much more out of the jet unit without it exploding😁, (it's only plastic I think, not GRP), - might have to buy a back-up and fit it with better quality bearings etc. If the jet was in the usual 'plastic' 24" toys it would be a rocket, but it's pushing 6lbs which is a challenge😀
Note the police chase outside in the background😁- always action around here, lots of hoons in cars😁
More changes, (not again you say😐) this time the original nozzle was re fitted, as I found that the very clever improvement I made, (a flasher, smaller, better fitting brass one), wasn't so clever after all (can't be brilliant all the time😁) and was restricting the flow. The performance was quite a bit better today (still not startling) and it seems obvious now that MORE POWER will be the next step (have a higher KV, 35 sized brushless coming on the sampan to try).
Had a chat with a long time expat UKer (ex British army) at the pond today, and he mentioned that he has an Aerokits fireboat 'kit' still in the box he hasn't started, (you might be able to hear the conversation) and that he was modelling in the 60s in the UK, running diesels in his boats. He was sailing a Kyosho Seawind today (as was the other guy),- and they look like a nice little yacht, and sail well.
British Power Boat Co. Type Two 63' HSL - ASRL 131
This 'Whaleback' boat is a 1/16th scale Air Sea Rescue Launch that was built by a friend of mine Graham. It is powered by a Turnigy brushless motor and Lipo Battery
I thought it the most appropriate music for this RAF boat at speed. I too loved that film from the first time my Mum took me to see it at the Savoy cinema in Colombo, Ceylon (Sri Lanka) when it was first released in 1964.
💡Scratch built from plans. Plank on frame. Large brushless motor,150 amp esc,length is54 inches custom made propshaft ballraced at each end and middle. Has running lights,and large very bright searchlight. Flack Mats were made by better Half. Everything else was scratch built by myself.
Just built Krick RO-Marin Neptun. First tug I’ve built, she came out okay, I think. 6volt system, MFA 2.5 geared motor, Graupner SXM switch controlling the lights, older Pixie brushed esc controlling water monitor pump. Old Futaba MC210 for motor esc, Frysky QX7 radio. This video was shot at Towne Lake, McKinney Texas. She well on her maiden, needs about 2-4 ounces ballast in the stern though.
Ahoy Maties! it's been a long time since my last posting. Happy 2019! I just completed my new scratch-built boat "Electric Barbarella". I tried to recreate (with some liberties) one of my favorite boats of all time, the 30-footer Chris Craft Sportsman built during the 1970s. it measures 24 X 8.5 inches. it is powered with a 9.6 NiMH 4200 mAh battery "nunchuck" pack (like the one used for paintball guns), brushless motor attached to a 30A Mtroniks Hydra controller and a 30mm M4 3-bladed brass propeller. The hull (my own on-the-go design) was made out of Balsa wood which later I fiberglassed. For the superstructure I utilized 2mm ABS plastic sheet material. To my surprise the boat turned to be a very stable and forgiving platform. I really feel a very close connection to this vessel as it is my first own hull design.😁
Just converted this 40yr old twin brushless model (scratch built from a Vic Smeed plan) to a proper independent twin system plus a sound unit. Started off with a 70s Futaba ESC on 27mhz, then on FM, then replaced with an Electronize unit on FM, then to 2.4 and now on 2.4 with twin ESCs and converted TGY S6 (twin throttles). Maneuvers a lot better and makes a better noise.
Nice job.Great to see a boat running built from a Vic Smeed plan.Should do good in a steering competition with the manouverability you have.Lovely boating pond.
Thanks for the nice comment, and yes it is a very nice pond, except when there are a lot of those things with rags tied to sticks racing (shouldn't say that as I've sailed full scale all my life and still have 2 small yachts), and the buoys they leave there are a pain also, (easy to forget they are there) it was full of hire carp (yes hire carp) which were removed as the council wasn't paying the company or some such hassle, but I'm sure they missed some and they will soon multiply and keep the weed down. Bought the plans for the MTB around 1968 and took around 20yrs to finish it. I still have the plans and it only took me about 40yrs to find a photo of the original boat (bit late by then!).
JB
Mostly a lot of time, (hate to work out the labour cost on any model at going rates,- probably in the thousands)!
JB