One of our club members built two dories that sailed in Spencer's pool in Burlington. The oars operated to propel the dory. Alex the Dory man is no longer with us . He had a tiny bottle of Skreech in the bow that someone walked away with. The lyrics describe Codfish Dan harpooning Halley's Comet, using the Big Dipper as a pot, and cooking fish on the sun—all while sailing through the cosmos in his golden dory. It’s classic Stompin’ Tom: full of Canadian pride, storytelling, and a catchy rhythm. Today's Question was about Dories, so I remember Alec's & his dory with fondness. The Moon-Man Newfie Stompin' Tom Conners.

Was asked for more info . So here are a few photos . This mini humidifier uses water only to generate fake smoke no smelly baby oil & varsol odor 50%-50% mix for Graupner smokers .I get the power to run unit from the receiver battery port as the unit uses a USD port to make it work so I got a old servo & cut the wire off it removed the signal white wire & used the black & red wires to power up unit . I have to turn model on then power up the Humidifier to start fake smoke put the cabin on model & away we go. Make sure Positive & Negative are put in proper receiver slots Please don't damage receiver if it's plugged in wrong.

Having done a bit more trimming the lee helm is reduced but a bit like squeezing a balloon it has given me other issues. Anyhow, Andy a proper sailor took her for a spin and after sort of getting to grips with the controls he then went racing with the df65's. Camera battery died before the end of the race but got loads of good advice for the next outing.😎

Tomorrow the Confederation Marine modeler's will have our first meeting & the theme is bring one of your oldest model boats . So here is my Billing's Cutty Sark Built in 1977 for my sister she took it to her in-laws Manor in Milford Bay Ontario their it stayed above the fireplace for 20 years .Property was sold & it then went Amestburg Ontario for another 20 years Then it was returned to me.

Managed to capture some video of Brian Clewes' live steam TID tug on the lake this Wednesday 19 October. First chance for a proper sail and a bit more ballast needed.

Had a little trouble getting my sound to work properly but with a little fiddling got it working a lot better had to reverse motor leads & switch transmitter forward -reverse switch so it would work in forward direction .

Second test was slightly better, using the aluminium spiral cut universal which came with the jet unit. As you can probably hear, it was horribly out of balance (even with cable ties to reduce it). It was not even drilled centrally and the spiral is right hand when it should be left hand, (like a spring twisted against the wind, it wants to deform). Slight improvement in speed on the first test (no slip this time) but the noise was horrendous.

Have pulled the jet apart and found that the 3 blade prop is around 1 mm too small for the hole, causing cavitation (see loads of bubbles in the jet stream) which is causing loss of thrust. The prop is the wrong type as well, with rounded blades, so I have modified a larger prop with more pitch to fit snugly in the unit to hopefully increase thrust. The shaft is also wrong, with a flat cut almost half the diam and carrying on through the bearing, allowing the grease to fly out.

I actually saw a Chinese site on Al Expr stating that "some dimensions on the product may be different due to the number of machines and operators involved in its' manufacture," SERIOUSLY!!??? their quality control must be utter crap and the operators not skilled enough to eat their lunch😐 Why bother having a dimension at all?? Little wonder nothing fits properly.

Unfortunately, most model shops sell the very same stuff, unless you want to shell out muchos dolleros for European stuff. I have just ordered some 4mm silver steel to make a new shaft, so a coupling or silicone tube will fit better. Also ordered some solid connectors to try. Vibration is wasted energy so it needs to be eliminated. Hopefully the mods will improve things and allow the motor to run on 4s rater than 3s. Worked out that the motor is only 1200KV, so it's only doing around 13,000 rpm under load. Probably will need around
18,000 rpm for proper performance. Onwards and upwards (or forwards as the case may be.😁)

Sorry about the blurry vid again, but my camera lens is knackered.

I finally managed to get out and do a video of SY Minnow. This was taken at Cheddar Steam Club and Jane and I were the only people there so had the water to ourselves. I have increased the displacement a little which has made her more stable in the wind. Although it doesn't look it, there was quite a breeze that day and you can see the boat heeling to the wind on occasions. I was very pleased with the mist unit as this was the first time I have seen it operate properly. I will do something about the masts being out of alignment!

" Elsa ", is a steam dredge barge built by Buxton Model Boat Club member Dean Ratcliffe.
She is roughly 1.24 scale, approximately 43 inches by 8 inches and is made from recycled and up cycled materials wherever possible. She has a single rudder and propeller, powered by a single motor from a drill, and two 6v lead acid batteries. She is a totally freelance design.

Found a way of pulsing the water using the pump of a dead smoker (Hen Long smoker that is) In this test I used a pump to prime the smoker pump (smoker pump on 2s) and the rest is just syphoning through the pump to the smoker. You can vary the amount of 'spitting' from the exhaust by running the pump at low voltage or maybe using a peristaltic pump with a small flow.

I did not connect the fan powered smoker unit as I ran out of silicone tube, but the result should be the same as the last vid but with 'spitting' water. Using the smoker pump for water is not perfect as it would need sealing properly, and it's cumbersome, but you will get the idea. I have ordered a couple of small air pumps, so might have another crack when they come. I'll use them at the exhaust to disrupt the water flow if they are powerful enough, rather than use the smoker pump.

Ahoy Maties! it's been a long time since my last posting. Happy 2019! I just completed my new scratch-built boat "Electric Barbarella". I tried to recreate (with some liberties) one of my favorite boats of all time, the 30-footer Chris Craft Sportsman built during the 1970s. it measures 24 X 8.5 inches. it is powered with a 9.6 NiMH 4200 mAh battery "nunchuck" pack (like the one used for paintball guns), brushless motor attached to a 30A Mtroniks Hydra controller and a 30mm M4 3-bladed brass propeller. The hull (my own on-the-go design) was made out of Balsa wood which later I fiberglassed. For the superstructure I utilized 2mm ABS plastic sheet material. To my surprise the boat turned to be a very stable and forgiving platform. I really feel a very close connection to this vessel as it is my first own hull design.😁

I am continuing to try to learn the way this forum is properly used. I want to publish here my photos of the construction of my sailboat Carina from scratch that I am publishing here. I will limit myself to photos that are useful to get a general view of the topics I am publishing