Steam Pinnace

199 is a steam pinnace of the Royal Navy, built in 1909 by J. Reid of Portsmouth. She is now owned by the National Museum of the Royal Navy, and is based at Portsmouth Historic Dockyard.[1][2][3]
History
During its restoration, the ship was misidentified and it became known as Steam Pinnace 199.[1][3] However, it was later determined that the ship's machinery originated from pinnaces 208 and 224, and that its hull, stern cabin, and funnel also came from 224. Despite these findings, the name Steam Pinnace 199 was retained.[1][3][4][5] Steam Pinnace 224 was built in 1909, and was assigned to the battlecruiser HMS Inflexible in 1916.[1][3] It was sold out of the Royal Navy on 6 August 1948,[3] and in 1952 she was sold to a private owner, renamed Treleague, and was converted into a houseboat located on the Thames.[1] During this time its steam machinery was removed, and replaced by a petrol engine.[4] After serving as a houseboat for about 20 years, she was purchased by an antiques dealer who intended to restore her.[1][4] However, the project was deemed too expensive and its hull was sold to the National Museum of the Royal Navy in 1979.[1][4]
Restoration
She was restored by a group called the Steam Launch Restoration Group, based in Gosport.[2] In 1983, she was given a boiler and compound engine from a similar steam pinnace,[1][4] found at the Royal Navy shore establishment HMS Sultan.[1][4] Her original steam auxiliary engines were found at a yard in Belgium.[1] During her restoration, the ship was given a replacement Hotchkiss 3-pounder gun dating from 1887, and salvaged from the sea by a trawler in 1980.[1][5] The gun has been restored cosmetically; however, it is not functional and the inside of the barrel is corroded.[1][5] The ship was finally recommissioned in 1984, and was kept in the Mast Pond of Portsmouth Historic Dockyard until 1998,[2][4] when she was brought to Gosport for a refit.[2][4] From 1999 to 2001 her machinery was given a major refurbishment.[4] Since then, she has taken place in many events such as the International Festival of the Sea, the Yarmouth Old Gaffers Festival and the Southampton Boat Show.[1][4] In May 2011, she developed leaks in her boiler tubes and was transported to the Maritime Workshop in February 2012.[1] She was given a refit, and she was relaunched in 2015.[1] Steam Pinnace 199 is preserved afloat in Boathouse 4 at Portsmouth Historic Dockyard.[2][5]

Recently purchased, some light restoration needed

British Power Boat 64 ft RNZAF HSL scratch built 36" R/C model with twin systems including sound. Brushless 2000kv w/cooled (pump) in-runners, 30A car ESCs, 2200mah 2s LiPos remote lights etc. Started off in 1940, new with the RNZAF and had many modifications over the years till decommissioned, including machinery reduced to twin 671 Greymarine GMs (from the original 3x 500hp Napier Sea Lions) which were finally removed around 7yrs ago and replaced with a single 650hp GM Detroit 8v92T1 (still does 20 knots in its latest configuration ! - see this on the photo gallery of this model) This boat is in far better condition than the ex Phil Clabburn restoration of HSL 102 (he didn't have much to start with) and the hull has never had any major rebuild apart from being glassed to the W/L. Even today there is no way most people would pick it for 80yrs old. Those hulls never age! (ie some of the beautiful 'Whale Back' conversions still around)

This is a restoration of a launch I was given that was found in a rubbish bin on a farm here in Auckland it is an old RCM ? plan built 'Fairacre' and was pretty rotten when I received it as it is made in balsa and had been wet for quite a while. I stripped it down, re 'planked' large portions of the hull and fiber glassed it, re- built the cabin, re- marked the deck planks, fitted lights, curtains (ex Graupner Commodore bits from the 70s I had kept), stern ladder, cleats etc. it is fitted with a 540 brushed motor (originally had an old Graupner monoperm) and 70s Graupner ESC and Using 2.4 Radio gear. I still have a few things I'd like to do such as a re-wire, fitting chine spray rails, better motor and maybe some safety rails, but for now it does the job.

MY Restoration project I got this boat off a good friend of mine and give it a face lift now it looks Grand. 😁

Police (Scotland) 1.12 scale. made from a Semi-Kit by Models by Design, built 2014.
This is modelled from the interceptor42 range by Safehaven Marine. This is my first full build of a model, having only done restorations previously.
Model length is some 42 inch, beam of 12 inch. (106cm x 31cm)
Power is by twin E-Max BL2826 Brushless motors and 1, 80amp speed controller running on 2 NiMH 7.2 volts.
Fitted with Action electronics Police siren, and with detailed rotating blue lights and searchlights.
I sail this at Cold Knap Lake Barry Vale of Glamorgan, and I am the Founding member of the Vale Of Glamorgan Model Boat Club.
Also included is my Portland Pilot interceptor 42 which was the original prototype from Models by Design which I purchased and added lighting etc, this runs on Brushless motor running on 12Volt lead acid.
Visit our website at http://vgmbc.org/

Scratch built to 1/24th scale this is a model of a famous coastal barge built in 1904 at Mistley for the Horlock fleet. Sailed to victory in the1928 Thames Barge Match with Chub Horlock at the helm she won five "firsts" in her one race - a feat never achieved before or since. You can read about this exciting race in Chub's biography "Mistley Man's Log". S.b.VIGILANT can now be seen at Topsham in Devon where she is under extensive restoration.

Both these models are scratch built Durban tugs in 1:48 scale.

Built J.R. More between 2011 and 2012 and is 41 inches in length. The original oil fired tug was built 1961 on the Clyde and was one of the last steam tugs to be built on the Clyde. This tug still exists at the Durban Museum and is undergoing restoration.

Started Sir William Hoy in 2013 and is 45 inches in length and I am still working on the fittings and finishing. The original coal fired tug was built 1929 in the N.E. of England.
Both model tugs have twin motors geared down 6 to 1 and have differential steering.

Model Scale 1/2" to the foot The plans were purchased from the Albion Trust and I visited their base in Ludham, Norfolk to get details.
The Albion is a Norfolk Wherry. Built in 1898, she served as a trading vessel and then as a lighter until being acquired by the Norfolk Wherry Trust for restoration and preservation in 1949. Since 1981 she has been moored at the Norfolk Wherry Trust Wherry base at Womack Water near Ludham. She is listed on the register of National Historic Ships in the United Kingdom.

This was in a sorry state when I acquired it but here it is after restoration and 2.4Ghz radio fitted.

J. R. MORE - LAST OF THE LARGEST STEAM TUGS BUILT ON THE CLYDE. The best looking tugs ever built!

This model is scratch build at 1:48 scale of the SAR&H Durban tug J. R. More, which was the last large steam tug built on the Clyde in 1962.
It took over 2 years to complete this model, which was my first scratch build from the modified plans of a sister tug called the F.C Sturrock, which was also stationed at Durban as the shift tug for that harbour. Other tugs of the class were also stationed at Port Elizabeth and Cape Town.

The J. R. More was the newer day tug in Durban, most often used to service the Union Castle ships and others in, out of Durban and remembered by so many visitors to South Africa of that time.

This model tug on the water has differential motor control, software linked with the rudder, can go about on the spot and a delight to sail as a model, capable of 6 or more hours on the water. Working Rotating Radar, lights and woop-woop sounder as per the original tug. I would also like to install the Telegraph bells, however these would drive fellow modellers to distraction, as they were a very distinctive sound and very regular, Implanted and well remembered by the crews and those in and around the harbour, even today. The engines on the other hand were almost quiet and by all accounts very reliable.

This model is ballasted mainly by two 7 Ah 12 Volt SLA Batteries for the main drive motors and a 2 Ah 12 Volt SLA (Aft ballast) for the Lights, Radar and Sound unit. All up weight is 14Kgs and capable of above scale speed from the two MFA 6:1 ratio Geared Motors driving two 4 bladed 70mm screws.

This model has onboard charge regulator circuit, built-in minature dual volt meter to allow quick on-board voltage inspection and single plug-in charge and regulator socket for charging all 3 Batteries together.

The actual full size J. R. More tug still survives and can be visited at the Durban Maritime Museum in Durban, South Africa. Local supporters are undergoing essential repairs, restoration and preservation with private and company financial support.

J R More is the only surviving large steam tug left of this class and as Important to the skills of the Scottish shipbuilders of the Clyde.

A recent purchase from a buy and sell website, soon for restoration, (along with the rest!!!!!!)