MY WAVERIDER APACHE 58IN ZENOAH 30CC PETROL POWERED I ALLSO RACE AT FLEETWOOD LANCS

OUTERLIMITS 70IN INLINE TWIN 58CC ENGINE PETROL I SAIL AT FLEETWOOD LANCASHIRE

Greetings from Hollywood, California. 😎 Many thanks to David Metcalf at Metcalf Moldings for his advice and for so graciously replacing parts I messed up. This craft has been swimming pool tested (after all we're in Hollywood) and it ran beautifully. Next stop is the local pond. I chose brass counter-rotating props. Those are lithium batteries tucked under the sides. I chose to recut the decks out of wood. Brits rave about plastic but I found it difficult to cut and forget about sanding down the edges. (I guess if you cut it properly you don't need to sand the edge.) Major mistake: watching a You Tube video that told me I should make brass joints using a Propane torch. it will make a good joint but it MELTS ALL THE OTHERS. There was a lot of learning here for me and thanks to David's fine kit I think I'm somewhat of a better model builder.

SemI Kit, I.e fibreglass hull and superstructure and wooden rubbing strake all the rest is scratch built. A very good sailer and very stable. Quick to build only a month and powered by 540motor and 35mm prop. Lasted for hours on one charge.

Finally Finished my ebay refurb, Sailing @ Mutual Model Boat Club Heywood

I made a wooden barge for my tugs to pull but found this too heavy so I asked my old firm to make me one in 4mm aluminium it has been fully seem welded and is water tight .I got them to powder coat the whole barge in black matt and I just added the red paint. The top just slides off so I can change the cargo I just wish that I had not made this so deep as it sits high in the water unless I add a load of ballast am using a 10 ltr water container at the min and its still work in progress

Built from a Traplet plan 2012, all wood construction with plank- on-frame hull. 385 direct drive motor with 3 blade prop, Mtronics 10amp speed controller and 8x AA 1600m/a batteries wired in parallel.

Built from a Traplet plan in 2013. All wood construction, JP 400 direct drive motor with 2 blade prop. 2x 3.7amp 7.2 volt NiMhd batteries wire in parallel and a Mtronics marine 15amp speed controller.

HI this was my winter project the hull was given to me by my son who got it at a car boot sale it had been on fire as it was driven by a petrol engine in now has twin brushless motors with 45mm props but going to put 50mm props on when they come as it needs a little bit more speed Built from a set of plans this my first go at this as I build from kits in the past cabins made out of 3mm/1.5m ply and some 1.5mm balsa wood . Hull was sprayed and the deck and cabins brushed with enamel paint.

This model of the tourist attraction in Liverpool a few years ago.Sadly after a couple of mishaps all four have been withdrawn from service. The model however survives. it was scratch built from photos and site visits by myself (Max Ferrie).There were no plans available. it is about 28inches long and roughly 1/12 scale.It was built almost entirely from plywood. As you will see from video it operates on land and water. it is six wheel drive using differentials on all wheels. When in water it is prop drive. it has two small electric motors for power, the wheel drive being very low gearing (too low really it goes very slow on ground). it was completed in 2010, and is filmed sailing at the portable pond at Toys For Boys in Waterloo in 2010. it has sailed at Hoylake MBC also.
It is powered by two 6volt 4AH batteries in series to give 12volts.

Scratch built 1/48 scale Mersey ferry Snowdrop in current use on the Mersey (ex Woodchurch)
Model interiors fitted out with tables chairs people etc and 72 leds light to Illuminate the interior saloons.
Just completed and maiden voyage on Hoylake Lake on the Wirral.
2.4Ghz radio and a bilge pump just in case. Sails a treat with 100 passengers. Extensive use of plasticard on superstructure. Fibreglass hull from own mould.
See sailing location at www.hoylakemodelboatclub.co.uk
Our club can supply the hull if you want to have a go at building one.

This style of launch is gaining popularity for fast crew and supply boats in the North sea.

This boat was designed by me from photos available on the web. The hull id fg, all the rest is plastic and wood