A recent purchase from a buy and sell website, soon for restoration, (along with the rest!!!!!!)

Hi" to all model boat builders. I thought I would add my new project to this fireboat website for all to see ! I bought this from fleabay as a total wreck. She is a rare Scratch built from a plan of a Walton Thames RAF ASRL launch at 36 inch long & 8 inch wide.took me approx 6 months to do the rebuild. Brush painted with 5 assorted colours with decals working lights ect.
Walton Thames is now running on a new Johnston speed 600 electric motor. 50 amp speed controller 45mm pitched propeller.A 6 volt at4.ah which gives good running time & good scale speed. Photos are taken at Eaton park Norwich England. Enjoy. 😊
My next project will be a 1950s Aerokits/Keilcraft Sea hornet. " So watch this space "

Built from light ply and balsa from a plan available on the Model Hovercraft Association website (under resources) www.modelhover.org it is powered by two 540 brushed motors with dedicated speed controllers.
This model has now been sold and replaced with a newly built Canadian Coastguard Griffon 2000TD built off a Mark Porter plan but using two Graupner Speed 600 motors, one powered by a 3000 Li-Po battery for thrust and the other on a 7.2v Ni-Cad for lift.

HI to all you Fire Boaters,
I have decided to finally bring my Fireboat out of the closet and up for inspection.
This is the first of my many boats I am showing, I will probably show others in the future.
I started to build her back in 2006 after being off work and having a shoulder operation. She was not going to be a R/C boat, just a bit of something to do whilst on recovery.

I have a 34" still in the box unmade, purchased back in 1994 from Aerokits.
I drew round all the parts and then shrunk them on my scanner. She is 27" long I think that's
just fraction over 1/20th scale . She is almost all balsa except the 2 under skins that are balsa laminated with 1/64th ply. The hand rails are 1/4" balsa blocks I cut from a strip and the rail is ally tubing.
The mast is made from plastic strip from packets from the model shop.

When I returned to work she was put into the shed and left unfinished.
I stumbled across the Fireboat website and registered in 2009 when I was off work once again. This then made me think more about working on her again and I decide to turn her into an R/C model. So out she came and I fitted an Electomax Delta 480bb motor and a M3sonik esc.
I also purchased a couple of Robbe fire monitors, put them together shortening the nozzles and cutting the bottom of the base of to try to look a bit moreto scale. I know they are not the correct type but if I want to go down the road of getting them working then these ones will.

Then off I went to Wilkinson's and bought some paint. Then set out to paint her, as I brushed on the paint it seemed to be drying almost as quick as I was painting her. Dragging the paint I had just put on with next brush stroke. What a TOTAL DISASTER !!. I gave up on her and back into the shed she went.

2010 arrived I started again rubbed the paint down a bit and bought some Tamiya spray acrylic and started spraying, underside red, it seemed look all right. I used a nice new roll of low tack masking tape, taped up the underside and the decking and sprayed on the black on the sides. I thought that look all right. Took off the masking tape, which also took off the red paint and the dope from the decks. Another DISASTER. Back in the shed she went once again.

A couple of months went by and I was up in Norfolk on my own boat and watching the workers in the boatyard, ideas came to me and when we returned home, out she came and I repainted the sides
and then with red oxide paint I painted her undersides to make it look like antI foul paint. I used some white stripe to cover the join of the two different paint colours.
I had bought some roundels in Anglia Model Shop in Gorleston and some lettering in a shop in Norwich and after painting put these on.
Not looking fantastic but passable I was a little happier with her, but still not satisfied, back in the shed she went again.

Now after so much nagging from my brother out she has come, I've started again. He talked me into changing and trying a brushless motor and a smaller esc he had in his tool box from his helicopter he was shelving as its rota head was damaged beyond repair.
I have now fitted them and if they work I will change the esc to a forward/ reverse esc in the future at some point.

Sea trials are still away off more than likely in the spring, because the decking has yet to be painted. That will be the next job.

I think that's all for now, as I have probably bored you all to tears. I hope update as I progress further.
Just to let you know I'm Tom (alias BOATSHED).

HI all, I was given this model in a rather sad state as it had been in a junk box in a farm out-building and had been subjected to the weather from time to time . it had been there for about 20 yrs or more and the balsa hull was 60% rotten . I think it was originally IC powered but had been fitted with a Graupner Jumbo 6v motor and an old style rheostatic sc, ( I did try using the sc but it sucked so much power I gave it a miss - also had no reverse)
Amazingly the motor and sc still worked and with a bit of oil and cleaning the motor is still running well ! I'm using a 1975 Futaba 24v 10A sc and 3cell LiPo which pushes it along nicely. I stripped everything and replaced large bits of the hull, (which was fun as every time you picked it up you would poke another hole in it it was so fragile !) I got it to the stage where it would hang together fairly well and glassed the hull which has made it like the proverbial "brick one". The rest was very careful sanding of the deck and cabin, (they were ply so fared a bit better) and a lot of little filling bits to get it right.
Nav lights and cabin lights all work from the micro switch board, the curtains are left over Graupner Commodore (1975), I've added a mast, new windows,flag pole, cleats, ladder and handrails. Any ideas as to its manufacturer would be great. I have seen another one on our local "Trade Me" web site recently.

veron police boat built from old copy of plan and info on river police web site .

free down load plan of swordsman scratch built looking for more plans Iam a new boy at 74 years old to model boat building so find your web site help full . larry

The boat is a scratch built and started life in the shed. it is a semiscale model at aprox 36inch, built with balsa wood.It is full remote control and fitted with two Mtroniks Vision 600 motors one 12volt 7ah battery,one seasprint esc.
It was built as a fun boat so I could sail with my friend Peter thomas with his variuos boats.
Several things have now been added since this boat was first built, IE smoking stacks, fireing torpedoes and magnetic pickups for colecting them. Also has working radar/moving gun + a home built bec.
Flag poles and flags/compas has been added on the superstructure.
Each motor draws 6amps at full power, I have measured the speed from one point to another at a spacing of 60mtrs, and timed at 15 seconds, but this is a bit fast for this boat as she starts to plane out of the water.
We sail her at New Brighton lake on the wirral most wednesdays. As the weather is now a bit cool I have just purchased a simular model to this at 1:48 scale 110ft island class USCG Patrol boat so I can look at them both in action when the weather picks up. Anyone wanting info can contact me via this website.

This is my ** version of the Sea Queen. My father owns one of the originals and when one lunch time I saw one on the ** web site I knew I had to get one.
It was to be a winter build project and work started in the autumn of 2006 and it was launched in May 2007. I was very disappointed to see the all white paint finish used on the ** advertisements and decided I was going to re-create the look of the original. Cosmetically the big problem was that the original used mahogany finish ply for the cabin sides and the ** version was just plain birch. However after a bit of staining I was quite happy with the finished colour. This was contrasted against clear coated lime wood deck planking.
Also ***a€™s bag of fittings missed out on the signature life belts so I had to make my own.

One Improvement that I did make was the inclusion of a dashboard, instrument panel and throttle slide.

The graphic on the transom was a custom cut from callie-graphics.

The supplied motor was replaced with an MFA Torpedo 850 which is a direct replacement. ( Same mount, same screw fixing centres etc ).
Battery is a 12V 7A gel cell, ESC is an Mtronics Marine Viper 40A