Some photos of my Aerokits Sea Scout taken yesterday at Southport model boat lake. Fitted with an outrunner brushless motor.

HI shipmates, here,s a few shpts of the "Port ".
She,s a 1/80 scale scratch built cargo ship of the Port line company from around the 1950,
A ship this size requieres quite a bit of balast, I use water, it takes around 40 lds to get her sitting right, this is pumped in and out with a submersible caravan water pump.
Most of the fittings are resin castings.
there are a few more bits to finnish off but could not resist the chance to try her out on the Chasewater pool.

Built from a .PDF plan I found on the net, this 22" Outrigger Hydro sports a Hobbywing 3600Kv Brushless, along with a Hobbywing 60A esc, a 5000mAh 11.1v 45C LiPo, and an Octura X435 Prop connected to a Strudder from Prestwich models.. it weighs 930g without the battery, with the battery, she goes 1386g.
This was it's Maiden run, at Herbert Woods Boatyard, at Potter Heigham Norfolk. it ran very nicely, but can do with a little tweaking to get more speed.
For the record, I did not swear, it was someone onlooking.

Built from a .PDF plan I found on the net, this 22" Outrigger Hydro sports a Hobbywing 3600Kv Brushless, along with a Hobbywing 60A esc, a 5000mAh 11.1v 45C LiPo, and an Octura X435 Prop connected to a Struuder from Prestwich models.. it weighs 930g without the battery, with the battery, she goes 1386g.

Ahoy
Here is something you dont see everyday, I built this from scratch made from pinewood. This consolidateds PB-2Y5 Coronado flyingboat, used as a trnaport and submarine patrol bomber.scale 1/72
Franklyn Day aka Boats

Both on display at Portis Head show
1/12 scale 33" and 54" long.

Built from light ply and balsa from a plan available on the Model Hovercraft Association website (under resources) www.modelhover.org it is powered by two 540 brushed motors with dedicated speed controllers.
This model has now been sold and replaced with a newly built Canadian Coastguard Griffon 2000TD built off a Mark Porter plan but using two Graupner Speed 600 motors, one powered by a 3000 Li-Po battery for thrust and the other on a 7.2v Ni-Cad for lift.

HI " I thought I would put my biggest model from my collection for all to look at ! HMS Avenger took approx 3 years to build . " She is a type 21 frigate at 1/64 scale . At 6 feet long . Scratch built on a fibreglass hull from plywood plastic card & metal parts . Works on a six channel futaba skysport .
Full working red & white leds on deck and cabin , lynxs helicopter with working rotor blades with landing lights. Working radars, bofor gun , A ships whooping sound . Runs on two speed 700 motors off a 12volt gel sell battery which give a good 1hr sailling time . Controlled by a 50 amp speed controller with two brass propshafts behind good size rudders which give a excellant turn .
My model HMS Avenger is a copy from the real ship in which took part in the Falklands war in 1982. Painted in the same grey with a green deck . She looks great on display or on the water . Avenger gets a lot of interest from the general public . please enjoy looking at the photos shown at Sheringham & Eaton park Norwich Norfolk .
" thank you .. A Prestney

HI Fellow Enthusiasts
Photo shows my RAF crash tender in the colours as it was when first built in 1956/57 from a kit. (Red tops like all fire engines, well I was only 9 at the time.) This photo was taken at lakeside in 1993 when I first joined the Cwmbran Modelling Society. The Second photo shows the boat on display at the Portis Head Open Day event in 2000 several modifications taking place to the overall look of the boat. in 2008/9 I decided for it's belated 50th. birthday to revamp the model and bring it closer to the real thing. Damage to the woodwork being repaired and a colour scheme close to that of the real boat being applied. Several new deck fittings being made along with new window surrounds made out of plastic replacing the cardboard ones fitted in 2000. New decals and correct flag also fitted. The model was entered in the 2010 society Chairmans Comp. winning joint first place with one of my other models. Photo 4 shows my model as she is to-day repaired once again ready to sail, after hitting some Ice over the christmas period 2010 resulting in a hole in the bow that almost caused her to sink.
The model over the 54 years it's been around has been fitted with single and twin electric drives and to day it has a single johnson 550 brushed electric drive via a 2.5/1 gear box run off two 7.2 volt racing packs in series. The torque generated being too great for standard plastic props resulting in me using 40mm three blade brass props. The motor controller is an electolize 15 amp unit and I also use one of their switch units to activate the water pump for the scratch built water cannons. The water pump being salvaged from a 1960's car washer system and still goes to-day.
Hope you enjoy the pic,s as much as Ive enjoyed this model over the last 50 years plus.
Regards
GreyWolf

Ahoy
Here is another of my RC collections this the Revell of Germany Corvette SNOWBERRY. My spouse got this kit 7 years ago for my 64th birthday. I never got one of these before I know that Matchbox made this kit and went out of buisness. in overal view this is the Matchbox kit. I was overjoyed when my wife present this kit to me.After opening the kit examining the contents in the kit the hull comes in four peices two bow sections port and starboard. Two stern sections Port and Starboard.. To my horror they gave me two port bow sections. all there to do is to email the company and filed a complaint about the problem but it got worse. with the instruction sheet in my hand I gave them the part No. I need the Starboard bow section 2 weeks later they sent me another port bow section now I have 2 of them. This time I gave them a piece of my mind, I finally called up the company and filed my complaints. they were very humbled over this and they opoligized greratly. 3 weeks later a UPS truck pulled in. the driver approached my door with a huge box and a package I wondered with excitement whats this of. They sent me a new kit and the starboard bow section. What a del of the century, you dont see that no more.

As to the kit a modlers delight this kit is loaded anyone who has built this kit will share the same experince to the attention of detail. the hull length is 36 inch,s scale is 1/72 there aree plenty of room for your RC gear it to can make a good static model as well. Mine is powered by a dumas 6.0 volt electric motor with speed controll. 2 channel system. to make a stronger model for RC opperation use epoxie. The hull comes in 4 sections leaveing no seams to fill. on back of the instruction sheet they give you a selection of color schemes and ships names. I like the north Atlantic color schedule. So I modeled mine as the Snoewberry. These kits still can be purchased I see thgem all the time on ebay.

Boats

I got this from another modeller late in 2010 sailed it at Westport in September. The plan is called HMS Midge but this type of boat were only known by numbers I.e. TB 20. it goes very well on 7.2 volts but needs a bit of ballast in the stern to stop it diving at speed

The weather on Sunday was great here in Peterborough and the perfect opportunity for the first trip out since restoration work was finished. The boat with ballast is very heavy so help from a few friends at the boat club was much appreciated! Performance from a pair of original Decaperms isn't earth shattering but good enough to give a nice scale performance, I might decide to upgrade them over the winter but haven't worked out what the best option might be so any suggestions based on your own experience would be appreciated. Thanks for looking, Roger