After going over everything to make sure nothing had come adrift after being upside down after painting, thought I'd give it a quick dry run (no water ) . Did the vid and found that YT had put the vid/sound way out of sync. Tried to sort it but gave it up as a bad joke. You will see the smoke start, and then a while later you will hear the engine start (they actually start together,- the smoke being on a 5 sec timer to allow the element to heat up before the air turns on, giving it a puff on start-up. )
You'll have to pretend you are seeing them together, (very annoying). Apologise for the 'music' as I had to create it myself using a free beat app to get round the YT copyright rubbish. It's only there as a demo, showing using the remote to change the volume.
That's very clever Peter, (10 points for that 👍) as long as it doesn't do a kursk, I'll be happy.
Hopefully do a better vid later, - YT's done this to a few vids for some odd reason.
JB
Seen here at Buxton is - 'Ellipsis' an International One Metre Class yacht .
Built from lines drawings purchased from the designer Frank Russell.
Neville hand laminated the hull in epoxy glass, and the fin and rudder in epoxy carbon. Hull finished in cellulose paint.
Information provided by Neville Black.
Made this in about 6 weeks for my son who was not interested so I now use it for general on water filming etc. It was scratch built from a few photos and is all balsa construction, sealed and painted. Powered by a single 12v 380 motor with a 28mm 3 blade prop. Runs flat out at around 15,000 rpm.
I haven't run nitro boats for a number of years now Doug, same with the planes, everything has been converted to electric long ago, (all the nitro planes included.) No more mess and smell of burnt fuel in the house, no having to take a roll of paper towels and soap sprayer and wash your plane or boat before putting it in the car, and no more having to put a plastic 'nose bag' on the planes to hang them up so you don't get oil dripping on your carpet!
Re- Graupner 'Premium Line', certainly sounds like their quality has dropped, you couldn't fault them in the 70s, gone the way of all the others due to competition from the home of Oolong tea by the sound of it.
"everything has been converted to electric long ago"
Know what you mean John.
I've still got a 5ltr canister of pepped up glow fuel kicking about in the cellar.
Probably degenerated into uselessness by now🤔
Maybe I'll stick in the car or use it to start the barby😊
Re Premium line-
Belfast wasn't so bad, but had the same crappy plastic props held on with grub screws.
So she's getting threaded shafts and brass props from Raboesch 😉
On Graf Spee though I noticed a lot of resin casting faults, evidence of air bubbles and smudged detail, as well as over / under-spray in the painting and lifting of the wooden decks.
Had to inject liquid CA glue round the edges to stop it peeling ☹️😠
Best thing on both ships were the faultless hulls with double skinning!😉
One thing surprised me with Belfast though-
the recommended SLA batteries don't fit! I couldn't get them in any which way 🤔
Not to worry, they go in my 1:72 destroyer with ease 😊
BTW I prefer lapsang souchong 😋
I have been building my scratch build PT 109 for the last 3 months, working sometimes only one or two evenings in the week. As you must all know you can only do so much before you have to stop and wait for glue or paint to dry :( but at last it is now completed, RC gear installed and a mighty 48" in length at 1/20 scale. Next will be the lake and a final trial run, I completed a 'bath' test a couple of days ago and it only just fitted in the bath but both motors run great. hope you like. Andy
Sounds good to me DELVEIN 👍 PLEASE start a Build Blog about your project.
I'm sure it would be an inspiration to many members, not least me 😉
I propose to fit the centre motor as a simple brushed job with independent control, as RHBaker did with his superb Brave Borderer MTB. Centre motor for cruising and manoeuvring, two outer brushless for full power 'action' manoeuvring. So far I've only renovated the hull, way to go yet.
Looking forward to the vid of your Sea Trials👍
Cheers, Doug 😎
I bought the Moorcock from a fellow boater and decided to rebuild her as the Moorcock. The hull was stripped bare and the prop-shaft tube removed and completely remade with a new prop. The hull was then repainted and the life boat and davits added The superstructure was cleaned up and remade with a Robbe spring loaded grappling iron added to the rear deck.She is powered by a 24v scooted motor salvaged from a garbage bin and has 4 x 12v 7amh SLA's to provide power. She is a good strong vesel to sail and is often used as a recovery tug.
Ahoy Maties! it's been a long time since my last posting. Happy 2019! I just completed my new scratch-built boat "Electric Barbarella". I tried to recreate (with some liberties) one of my favorite boats of all time, the 30-footer Chris Craft Sportsman built during the 1970s. it measures 24 X 8.5 inches. it is powered with a 9.6 NiMH 4200 mAh battery "nunchuck" pack (like the one used for paintball guns), brushless motor attached to a 30A Mtroniks Hydra controller and a 30mm M4 3-bladed brass propeller. The hull (my own on-the-go design) was made out of Balsa wood which later I fiberglassed. For the superstructure I utilized 2mm ABS plastic sheet material. To my surprise the boat turned to be a very stable and forgiving platform. I really feel a very close connection to this vessel as it is my first own hull design.😁
A Little bit forward , the hull is ready for paint and im going to mount propshaft and motors , im going to work with the superstrukture so it will be ready
last pictures l posted l painted the wave princess l changed my mind and decided to go for some planking on the decks and cabin roofs l have also done a little bit of tarting up using some brass welding rod and brass tube l am quite pleased with the out come so far. these piccys are about a month old now so she has had a god rub down and given six coats of clear varnish. l will post more piccys when l have installed the windows and frames.
Sooo glad you went for wood and not paint👍
BTW How did you manage to enlist God's help?
Didn't know HE was a model boat enthusiast!
But then again HE did command the building of the Ark 😁
Yours tongue firmly in cheek, Doug 😎
Huson 24 RC sailboat wooden hull. I have a small fleet of these. They are extremely stable in high wind. Bought this one online in pretty good condition.
Did a lot of smoothing on the epoxy coated hull. I use West Systems epoxy because it flows so well - like paint - and doesn’t stink.
Proboat Alpha - ready to run, model of PBR, Patrol Boat Riverine, used by US Navy during Vietnam conflict, served 1967 -1972.
Images show basic detail, 1/18 scale, with crew. Bow gunner servo is linked to rudder. Comes with Navlights, looking forward to a night sail.....some painting added to weather craft, as well as painting radar housing a lighter grey....and the canvas roof over wheel house....a little artistic licence with vessel numbers......Brown Navy did'nt always have numbered vessels....but could'nt help myself.
I thought as the lake is still full of weed this would keep me sailing built from light ply fibre glassed inside & out then painted length 33" width 12"height 16" to top of the prop
70 amp esc aircraft brushless motor 11" prop
I am busy with a landing craft i thought this would be another one to beat the dreaded weed 😱
Hopefully do a better vid later, - YT's done this to a few vids for some odd reason.
JB