This is a Kitshack 46 inch Crash Tender. Nearly finished with a bit more detail yet to finish powered by 2 1400 kv brushless motors running on car speed controllers at 7.2 volt. Goes like stink! Has working rotatable fire monitors which are scratch built

SS Talacre - Single Hatch Coaster 1:48 Scale Just recently bought second hand and about to renovate to my own standard!
Caldercraft SS Talacre
The SS Talacre is a typical single hatch coaster used in the coal trade of a type that was found by the hundreds around the coast of the U.K. in the golden era of steam. Designed for Point of Ayr Collieries by Crichton, Thompson & Co Ltd., of London she was built by Crabtree &Co., of Great Yarmouth in 1917. Talacre was named after a small village near the colliery. Talacre was finally scraped in 1959 by the Hammond Lane Foundry in Dublin. Realism leaps out of the completed model, as if a turn of a valve will start the anchor windlass or the cargo winch clattering away and the lagged steam pipes to begin steaming and drying out.
Scale: 1:48
Length: 863mm
Beam 152mm

I made a wooden barge for my tugs to pull but found this too heavy so I asked my old firm to make me one in 4mm aluminium it has been fully seem welded and is water tight .I got them to powder coat the whole barge in black matt and I just added the red paint. The top just slides off so I can change the cargo I just wish that I had not made this so deep as it sits high in the water unless I add a load of ballast am using a 10 ltr water container at the min and its still work in progress

Different from my usual models this is a static model in a glass case but a model boat never the less. it was made to commemorate the centenary of the foundering of the isle of Man Steam Packet vessel Ellan Vannin in the Queens Channel on the River Mersey Liverpool UK on 3rd December
1909 with the loss of all lives. The model is constructed almost entirely from scrap cardboard. She is presently on display in the Crosby Coastguard station but this is closing soon so the models fate is in the balance.
She was made to be displayed at the commemoration ceremony on board a Mersey Ferry in December 2009.

This is a Chris Brown fibreglass hull for Cariad, it was a reject so Chris let me have it cheep. I like to be different so I built it as Spray of Newport. Sailed well on internal ballast only just adjust the rig to suit the conditions. Two sail arm servo one on main other on fore sails. Rudder controlled from under the deck by servo 3. The westerman ( who sails the boat for the pilot) holds the tiller which moves his arm. A forth servo pulls a string passing up his leg through his arm which is a spring. When the spring is compressed the arm waves in a random way. ( the idea came from the toy animal on a stand when the bottom of the stand is pushed in the animal falls down.)

HI this was my winter project the hull was given to me by my son who got it at a car boot sale it had been on fire as it was driven by a petrol engine in now has twin brushless motors with 45mm props but going to put 50mm props on when they come as it needs a little bit more speed Built from a set of plans this my first go at this as I build from kits in the past cabins made out of 3mm/1.5m ply and some 1.5mm balsa wood . Hull was sprayed and the deck and cabins brushed with enamel paint.

Scratch built 1/48 scale Mersey ferry Snowdrop in current use on the Mersey (ex Woodchurch)
Model interiors fitted out with tables chairs people etc and 72 leds light to Illuminate the interior saloons.
Just completed and maiden voyage on Hoylake Lake on the Wirral.
2.4Ghz radio and a bilge pump just in case. Sails a treat with 100 passengers. Extensive use of plasticard on superstructure. Fibreglass hull from own mould.
See sailing location at www.hoylakemodelboatclub.co.uk
Our club can supply the hull if you want to have a go at building one.

Built from a plastic hull given to me by a friend who bought it at a car boot sale the hull has been reinforced with fibreglass then like most kitShack
builds a box was made to hold the running gear it will be powered by a brushless airplane motor & 11.1v lipo battery
I will post more pictures as it progresses

Scratch built out of wood and fibre glassed with a car fan heater motor on 2.1 reduction

Following the legendary Keil Kraft Eezebilt plans for a Mermaid Ocean going boat. Plans exploded to 200%. Trying to build it completely out of Plywood and Foam Board.

OA Length 710 mm, Beam 180 mm. AUW 1.98Kgs.

She carries the name 'JAYSHIL". it is a portmanteau derived from the names of my late parents.

Model features working lights as prescribed by the international Maritime Authorities:

http://www.bosunsmate.org/seamanship/lights.php

In keeping with Rules 22 and 23:

http://www.bosunsmate.org/seamanship/rulesoftheroad.php#rule23

Brushed 550 motor, Reversible ESC, 2S LiPo, Turnigy Blue Prop, Working Lights and indigenous Sound Generator unit.

Video is available here: (you may need to turn down the volume a bit as the horn is rather loud)

I would welcome any queries and/or comments on this build.

Thanks and Regards,

VC

HI fellow model leers.this is my latest model.Built in 1926' for the Ffyfe(bananas) family. Originally it was run on steam,but in 1939 converted to diesel,this was kept until 1957 when all the staterooms were replaced by cargo holds . She was then made into a feeder bringing eleven thousand boxes from Rotterdam to Southampton. She was scrapped in the seventies.my model of her was from 1926 the scale is approx 1/30th her length is 48 inches including bowsprit, and has a beam of 10 inch amidships. She is totally scratch built, plank on frame, all the decks are individually planked with black card in between , wheel house and all other parts are mahogany. She runs on a decaperm geared motor @ 6 volts, and the lighting system consists of 10 accommodation lights, port and starboard , wheelhouse, and both mast headlights,the large saloon skylight is also lit up with a set of disco lights on a separate circuit. The funnel houses a heavy duty smoke unit switched on by switching unit.

First stage of building the Cossack. I plan to build the hull out of fibreglass, the mould has been carved out of extruded foam. Then the foam will be covered in packing tape, then covered in fibreglass. Once the fibreglass has set the foam will then be removed from the fibreglass hull.

7 September, hull has been completed, started to build the superstructure