this is my new project of a tamar 1/12 lifeboat,a fantastic kit to build many parts to make up from brass and other bits,its very rewarding

HMAS Fremantle (my first build and is still a work in progress) is a semI kit, hull and some fittings were supplied, most parts have been scratched built. She is powered by two MFA RE-385 5-Pole DC Motors, each controlled by a Mtroniks MicroViper Marine 10 ESC, supplied by one 6V 3.4 Ah lead acid battery, she has a running time of approx 90 minutes on the lake.

This model was scratch built from US Coast Guard plans. The boat is constructed of balsa wood and the hull coated with fiberglass resin. All the deck gear is scratchbuilt from brass, the propellers, led's and figures are the only commercial parts. Scaled at 3/4=1 foot the model measures 42 inches in length.
It's powered by a Pittman 12 volt motor and controlled by a 4 channel radio. Working features are running and spot light, siren with flashing blue light, sweeping radar antenna and deck lights. Built in 1985 the model the lifeboat is accurate in appearence for that time period.(The prototype has been modified since).
The actual lifeboat is attached the the Coast Guard's Motor Lifeboat School at Cape Disappointment and is one of four boats of this class.

Well, it took 24 years of "on again-off again" building but now its finished. I started the model the day we put the CAMPBELL in commission(I'm a plankowner) in 1988.The model measures 6 feet in length and is scaled at 1:48. The entire model is scratchbuilt from wood (hull, superstructure, deck) and few commercial parts were used. it's powered by two Dumas 12 volt motors as a direct drive system. I had hopes of adding working features such as lights, rotating radar antennas, articulating gun, working anchor but I was just happy to get it finished! it will probably make at least one run at the lake come springtime but the models ultimate "homeport" will be a museum, at 6 feet in length(and 40 pounds of ballast) it's a bear to handle just to get it into the car for transport. Still, I'm happy with the results, it was a model of a lifetime(but I'd never build another one like it)! 😉

Got this one off ebay, had to use a little artistic licence with the paint scheme as club has several members with same scheme, so didnt want to look the same. The one thing I could not get over was how many parts were left over from the revell kit. Have a 380 motor in it with a msoniks 15 amp esc, could not get over how much ballast was needed to get her to sit in water true, but got there in the end. Now working on making homemade smoke generator to go in funnel, first tests great using nichrome wire and 6v battery, just have to make housing to go in funnel. Have tested parker black ink mixed in smoker fluid and effect looks fantastic.

Just bought this thought it was a complete kit, but alas it missing its superstructure parts, which I will make from scratch. its other wise OK.

HI to all you Fire Boaters,
I have decided to finally bring my Fireboat out of the closet and up for inspection.
This is the first of my many boats I am showing, I will probably show others in the future.
I started to build her back in 2006 after being off work and having a shoulder operation. She was not going to be a R/C boat, just a bit of something to do whilst on recovery.

I have a 34" still in the box unmade, purchased back in 1994 from Aerokits.
I drew round all the parts and then shrunk them on my scanner. She is 27" long I think that's
just fraction over 1/20th scale . She is almost all balsa except the 2 under skins that are balsa laminated with 1/64th ply. The hand rails are 1/4" balsa blocks I cut from a strip and the rail is ally tubing.
The mast is made from plastic strip from packets from the model shop.

When I returned to work she was put into the shed and left unfinished.
I stumbled across the Fireboat website and registered in 2009 when I was off work once again. This then made me think more about working on her again and I decide to turn her into an R/C model. So out she came and I fitted an Electomax Delta 480bb motor and a M3sonik esc.
I also purchased a couple of Robbe fire monitors, put them together shortening the nozzles and cutting the bottom of the base of to try to look a bit moreto scale. I know they are not the correct type but if I want to go down the road of getting them working then these ones will.

Then off I went to Wilkinson's and bought some paint. Then set out to paint her, as I brushed on the paint it seemed to be drying almost as quick as I was painting her. Dragging the paint I had just put on with next brush stroke. What a TOTAL DISASTER !!. I gave up on her and back into the shed she went.

2010 arrived I started again rubbed the paint down a bit and bought some Tamiya spray acrylic and started spraying, underside red, it seemed look all right. I used a nice new roll of low tack masking tape, taped up the underside and the decking and sprayed on the black on the sides. I thought that look all right. Took off the masking tape, which also took off the red paint and the dope from the decks. Another DISASTER. Back in the shed she went once again.

A couple of months went by and I was up in Norfolk on my own boat and watching the workers in the boatyard, ideas came to me and when we returned home, out she came and I repainted the sides
and then with red oxide paint I painted her undersides to make it look like antI foul paint. I used some white stripe to cover the join of the two different paint colours.
I had bought some roundels in Anglia Model Shop in Gorleston and some lettering in a shop in Norwich and after painting put these on.
Not looking fantastic but passable I was a little happier with her, but still not satisfied, back in the shed she went again.

Now after so much nagging from my brother out she has come, I've started again. He talked me into changing and trying a brushless motor and a smaller esc he had in his tool box from his helicopter he was shelving as its rota head was damaged beyond repair.
I have now fitted them and if they work I will change the esc to a forward/ reverse esc in the future at some point.

Sea trials are still away off more than likely in the spring, because the decking has yet to be painted. That will be the next job.

I think that's all for now, as I have probably bored you all to tears. I hope update as I progress further.
Just to let you know I'm Tom (alias BOATSHED).

Hi" I thought I would put my new rebuild on for all to see ! I found this old Marblehead yacht as a wreck. She was gathering dust in an old reclaim ferniture wherehouse whilst we were on holiday last summer. Been told the yacht had been originaly scratch built in 1950s from a plan. She took me about half a year to rebuild. New parts as follow hiteck sail arm winch with 18lbs of torque. New futaba servo for the rudder. New sails & booms rigs & fittings. New deck made from plank strip wood & varnished. Also finished in painted Ivery white. She sail well in lite to strong winds At my local boating lake at Sheringham Norfolk .
works well on a Spekrum DX5E But can work on any other 2 channal transmitter .
Hope you enjoy the photos .

HI " I thought I would put my biggest model from my collection for all to look at ! HMS Avenger took approx 3 years to build . " She is a type 21 frigate at 1/64 scale . At 6 feet long . Scratch built on a fibreglass hull from plywood plastic card & metal parts . Works on a six channel futaba skysport .
Full working red & white leds on deck and cabin , lynxs helicopter with working rotor blades with landing lights. Working radars, bofor gun , A ships whooping sound . Runs on two speed 700 motors off a 12volt gel sell battery which give a good 1hr sailling time . Controlled by a 50 amp speed controller with two brass propshafts behind good size rudders which give a excellant turn .
My model HMS Avenger is a copy from the real ship in which took part in the Falklands war in 1982. Painted in the same grey with a green deck . She looks great on display or on the water . Avenger gets a lot of interest from the general public . please enjoy looking at the photos shown at Sheringham & Eaton park Norwich Norfolk .
" thank you .. A Prestney

HI Fellow enthusiasts
The first photo shows the boat as it was bought from an E Bay auction in late February for the price of 14.50, for that price I had to bid on it, even thought I had a new kit of the same model on order from a model shop from the end of December, before VAT went up. The models turned out to be the 4 feet versions some 11 inch wide and now is about 19 inch high. This model turned up several days before the new kit turned up, and was a bit worse for ware than anticipated as the deck had started to part company from the hull. After stripping the deck of all remaining deck furniture the deck was re laminated to the hull, prop shafts and rudder tubes also refitted using plenty of resin and cloth. A rubbing strip was fitted around the deck hull line to tidy up the visible damage. When I was happy with repairs the hull and deck was rubbed down and sprayed. Using the information in the new kit and some photos of actual boats, MJB's (My junk boxes) supplied all the required parts to scratch build 90% of the models fittings as seen, this includes the figures on the deck. These being obtained off an EBay site as 1/24 unpainted train scene figures that required some or may be a lot of adjustments to their appearance. Several items have still to be made and fitted. As I'm working on her sister boat P147, will make extra parts in one go.
The boat has twin electric drives, the motors, MFA 919D series, are fitted with their own 2.5/1 gearboxes and they drive 40 mm three bladed conta rotating brass props. They have independent 15 amp Electonize speed controllers run from two 7.2 volt packs in series. The switching arrangements for lighting has still to be finished off. Don't know if I'll fit a sound system as the boat is for my grandson.
The boat has had several trips on the Society's water at Cwmbran with myself and my grandson at the helm. it seems to go fast enough for him. (The new boat P147 has been built with triple screws.) Can't wait to see both models on the water together.
Hope you have enjoyed the pictures and information.
Regards
GreyWolf

Bought this kit from Cornwall models ,great fun to build and fairly easy ..At the moment I am in the process of motorising all the move-able parts,Crane rotate and lift lower,Thruster and lighting..My mate from work is a spark and shows me how "to do it " electrically or Im lost.The relay is home made and powers the Bow Thrusters if anyone wants to make one of their own I have a few better pictures to show the wiring in detail . Most will know of this site but if not you can get some excellent items for your ship builds with a good quick service my home made relays switches etc come from here
http://www.technobotsonline.com/

HI fellow model boat people,just a couple of photos showing a rescued aerokits sea queen circa late 50s.
This was in poor condition, work was started mid January to strip down the various parts that required to be remade, deck/superstructure/roof panels/windows etc.
The hull needed stripping back to give a good surface for the finished paint work.
Completion of the basic boat is now getting near, and ready for fitting out with motor radio etc.
Hope to give more details later.
Cheers for now.