Recent Wee Nip convert graham93 displays his "spanking" new Wee Nip at Buxton.
Graham incorporated roller bearings in the gooseneck to reduce friction.

Seen here at play with Fiesta and Windstar.

Robbe WindStar - owned and sailed by Barry who is a member of the Buxton Model Boat Club.
Listen to video commentary for more details .

In light to medium wind , even with just one servo on rudder only , the "Nip" is in its element tacking within a desired arc.
Adding the second servo for winch control provides adequate range for tighter tacks and broader reach/ runs.

Get the best mast position established - then just "SMILE" !.

Using the Hobbyking Swamp Dawg as a platform for my Gopro action camera.
Managing slide, drift and wind rotation was a challenge in varying conditions, to help tame the beast we tried a few basic options !.

here my robbe smaragd in heavy wind conditions !
sails like a beauty 😁 for an old big lady !

This is a first try at a simpler quieter smoke unit. I used the smoker box/element off the Heng Long tank/car smoker unit with a 40x40 5v fan (the fan being voltage controlled by a 5v UBEC and the lot being run by a 2s Lipo (with a y splitter for the fan UBEC and the element using JST leads. Doesn't smoke that well as I had broken then repaired the element previously, but the other one I have smokes a lot better, and has a better type of element (possibly a newer version) Some photos etc on the smoker discussion. Unit is almost silent (the noise you hear is the camera and outside noise, as the window was open)

last pictures l posted l painted the wave princess l changed my mind and decided to go for some planking on the decks and cabin roofs l have also done a little bit of tarting up using some brass welding rod and brass tube l am quite pleased with the out come so far. these piccys are about a month old now so she has had a god rub down and given six coats of clear varnish. l will post more piccys when l have installed the windows and frames.

This yacht was purchased on a whim ? i spotted it for sail locally and thought it was about 30 inches high.
i had a shock on collection as its over 40 inches high and 3foot long.lt needed some attention to the electrics and transmitter and a lot of tlc. i think its big enough for my jack russell to curcumnavigate the world single footed !

made from a krick felix launch kit.As usual i have made slight changes especially in regards to the final finish of medium oak stain.
The original windows were cut from a sheet using templates provided and some did not fit as they were on the small side.i used some plastic sheet i had to make my own replacements.I also changed the prop coupling for a universal joint(i always do)
I prefer the less is more approach to some models.

Huson 24 RC sailboat wooden hull. I have a small fleet of these. They are extremely stable in high wind. Bought this one online in pretty good condition.
Did a lot of smoothing on the epoxy coated hull. I use West Systems epoxy because it flows so well - like paint - and doesn’t stink.

Assembled in 1986. Came out of loft storage, fired up and R/C after 15 years, in August 2018. Shown here at Millbrook Lake, Cornwall. A Krick model - well documented for its origins on their webpages, but steam power arrangements have been updated from this, the so-called "Puffin" arrangement, which was the available and recommended one at the time 1.5 bar pressure and about 20 minutes running time, but often wind-dependent on keeping the gas flame intact!! With a condenser fitted, a very realistic model and great manoeuvrability... and fun!!

Model is 49” long and with ballast keel added weighs 17 lbs. hull is covered with 2 layers of 2 oz. cloth fiberglass cloth and painted with Krylon spray can paint. Hitec sail winch servo for main sail and standard servo for jib. Model has auxiliary 6 volt electric power to compincate for my sailing ability’s and wind conditions.
Sails are Mylar.