"Searcher" was a Graham Goodchild design offered as a free plan in "Model Boats" in December 1981. Here is my version , many years in the building and finally nearing completion. Access to the hull on the original design was via a hatch above the cockpit - I had no faith in my ability to make it water tight so went for removable grp. hatches. The model is activated by a reed switch just in front of the rear hatch, which saves me the hassle of doing/undoing all the nuts (this had not been fitted when I took the first picture). The rear hatch gives me easier access to the drive coupling. The name "Nimbus2" is in honour of one of Dan Dare's spaceships in the Eagle comic. The third picture shows the ship in its final state with added 'enhancements' and working lights.

This are photos of the biggest and very well made model of the Endeavour, a sailboat from the beginning of the 20th century. the First photo is of the gentleman that build this fantastic model! I was allowed to publish photos you can see here. I myself feel obliged to stand-out and show the gentleman responsible for this work of art!

Trying to learn to use this forum properly I am publishing a video that shows an experiment I did to find out how fast the stepper motor could turn. I am using in my model of the sailboat Carina 2 stepper motors like the one shown in the video to work as a winch to control the position of the sails in a system solution where I am realizing this my own way to implement the sheets as shown on the original sailboat Endeavour. This requires my sheet control system to control the length of the sheet of the mainsail i.e. over a range of 8.3 meters. This requires the drum which is turned by the stepper motor to make 21 full turns. Details will be published in my report from scratch of building my Carina.

Proboat Alpha - ready to run, model of PBR, Patrol Boat Riverine, used by US Navy during Vietnam conflict, served 1967 -1972.

Images show basic detail, 1/18 scale, with crew. Bow gunner servo is linked to rudder. Comes with Navlights, looking forward to a night sail.....some painting added to weather craft, as well as painting radar housing a lighter grey....and the canvas roof over wheel house....a little artistic licence with vessel numbers......Brown Navy did'nt always have numbered vessels....but could'nt help myself.

Bravo Zulu Chaps😉

On Sunday our model boat club did a show at Hamilton's Steam Museum . Kind of hard running model & recording video at the same time but I managed to not run into any ones boat .

A great display put on by the SRCMBC crew. 👍

A tour around the many club stands at the international Model Boat Show. Full playlist of videos from the event here,
https://www.youtube.com/playlist?list=PL8iHs7pgHqAYXFGEi8-KfQXZOpYa4esno

Westbourne is a Port of London Authority steam Tug from the Caldercraft Mini-Fleet Range - it is 1:48 scale. This model was discontinued a few years ago but I did manage to purchase a brand new boxed one via ebay a couple of years ago.

During her time Westbourne was hired by the Royal Navy as a rescue tug. She saw service with them between October 1916 and July 1919 in the HM Dockyard. Prior to that she was on general towing service duties on the Thames.
She can be found mentioned in “SHIPS OF THE ROYAL NAVY, 1914-1919 - by TYPE & CLASS
Section 3. SUPPORT and HARBOUR VESSELS”

Following the first world war ‘Westbourne’ was one of three tugs attached to the Port of London Authority (PLA) Dredging Service, they were the "Westbourne", "Thorney" and "Brent", they were all fitted with a drag and under running gear.In 1940 during the Battle of Britain. ‘Westbourne’ and many other tugs were used in assisting the berthing of these large ships that entered the Thames.
The photos show from box to construction plus her on the water.

Building a German Police launch right now and thought that the radar scanner components were a bit 'heath robinsonish', so decided to see if I could make an alternative unit.

Photo 1 shows the Radar scanner parts obtained from MMB (ebay) for the princely sum of ONE POUND !!!!! plus 28p postage, and construction is of a medium soft resin that isn't prone to breaking or splitting when shaped or drilled, and a short length of 2mm brass rod becomes the drive shaft. This particular unit has a 44mm sweep bar but there are many other sizes available

Photo 2 shows the drive motor which operates on voltages between 1.5 and 6v, ideal for the control driver which is the next item. Available from saih.tan on Ebay for under 7 pounds, and if the motor is mounted on a removable bracket as I have done, this unit can be used in several models without the need for major 'surgery', the motor and radar shaft being connected with a short piece of rubber tubing

Photo 3 shows the receiver driven radar motor speed control which operates from an auxiliary receiver channel and takes the motor voltage from the main receiver supply, thus obviating the need for a separate supply and switch.
This unit is available from www.mr-rcworld.co.uk and costs a staggering 14.50 post free sheesh !

I must add here that I am in NO way connected to any of the suppliers mentioned here, but just though some other modellers may be interested in 'home brew' accessories and suchlike.

Various boats on the water at Southern Model Show 2017

Always interesting things to watch Hovercraft and these were 3 very different types.

Lifeboat Enthusiasts' Society demonstrate a huge array of super scale boats at the international Model Boat Show. Enjoy !