I hadn't built a model of any sort since I was 15 years old and that was a control line aeroplane with a glow worm engine. 45 years later and regressing nicely back to my teenage years, my wife bought me (reluctantly!) a RC Boat Kit - Mowe 2. I had been wanting to build again for many years, but children and family and home situation did not allow.
So, over the cold Autumn and Winter Months I carefully put my spare nights to good use, rather than watching night after night TV box sets and re-watching the entire James Bond movies, not once but 2 or 3 times....
Anyhow after 3 months...the finished product. I should have started a blog but didn't know of this site until a few weeks ago.
Not a brilliant finished job, but a satisfying one, and it sails nicely on Bushy Park boating lake in Kingston-upon-Thames.
Now o nto bigger and more complicated things...a Fairey Huntsman 31.
This time I'll do a blog....👍

Built as a rescaled version of a free plan in Model boat magazine (Dec 2009) now scaled to 1/16 to allow rc tanks to be carried

Grace is my first and favourite rc model. I bought this for a bargain £70 on ebay, requiring a little care and attention. She sails beautifully and looks good in the water. She sits low and looks like a trading barge from days gone by.

Well, it took 24 years of "on again-off again" building but now its finished. I started the model the day we put the CAMPBELL in commission(I'm a plankowner) in 1988.The model measures 6 feet in length and is scaled at 1:48. The entire model is scratchbuilt from wood (hull, superstructure, deck) and few commercial parts were used. it's powered by two Dumas 12 volt motors as a direct drive system. I had hopes of adding working features such as lights, rotating radar antennas, articulating gun, working anchor but I was just happy to get it finished! it will probably make at least one run at the lake come springtime but the models ultimate "homeport" will be a museum, at 6 feet in length(and 40 pounds of ballast) it's a bear to handle just to get it into the car for transport. Still, I'm happy with the results, it was a model of a lifetime(but I'd never build another one like it)! 😉

HI Fellow Enthusiasts
These pictures show my scratch built RAF Air Sea Rescue launch 2507. it was built using my own scaled up planes over the period July 2006 to August 2008. its approx. 4 feet long by 11 inch wide and stands 24 inch high.
The boat has twin Johnson brushed electric drives via 2.5/1 reduction gearboxes with three bladed 40 mm brass props. The speed controllers being 15 amp Electronize supplied from 4.5 amp D cells made into a 12 volt battery pack.
The boat sound system consists of a Diesel sound generator and machine guns being fired by an electronic ring counter circuit that allows the guns to fire individually or together depending on their selection via a diode network. The unit is switched on and off via a Electonize switch unit that also switches the boats lighting system on and off.
All the special fixtures required for this model being self made this includes the figures found on and in the boat. The basic figures are usually obtained from car boot sales or the local ÂA£ shop for next to nothing and then modified to the model boats requirements.
Launch 2507 was commanded by F/O W. Garret who reputedly made the most northerly pick up on the 26th June 1944 for the crew of a downed Catalina, for this action he was awarded a M.B.E. The Catalina pilot F/Lt. Horner R.C.A.F. died of exposure and was awarded a posthumous V.C.
I hope you enjoyed the pics and information.
Regards
GreyWolf

1. The sorry state of the Hull on the Fire Boat. Purchased from Ebay about 6 months ago, only now just started working on refurbishing it, it was covered in car body filler.

2. After about 2 weeks of very hard work it looks much better. it is running on a Johnson 600 size motor and 6v Gel Battery for its first sail at the Cwmbran Model Society tomorrow, so I hope that is will be OK. it does not appear to be an Aeroits model as the cabins remove from the hull. Not just the Cabin tops. I will try and supply some action photo's later.

I've been tidying this beauty up for a while now, no major work because it's almost all original. I've repaired her bottom and replaced the old bobs boards with modern RC gear from Action Electronics. She looked scruffy at first but much of the problem was smoke discolouration, after careful use of T cut it still seems to have a slightly aged look (like me) which I'm OK with.
Hoping to trial in the next couple of weeks if I can lift it once the lead ballast is in. I'd like to get her to the Funday in September - fingers crossed.

This is my second attempt at scratch building using a a grp hull. My first boat was an MTB/MGB built on a Perkasa hull as a semi-scale model. (see All things Rc - Power setups).
This time I have concentrated on keeping things lighter but it still weighs in at 2.5kg!
I have built without plans, relying on internet photos scaled etc using "Photo deluxe" and "Photo Express".
Virtually everything is built from plasticard apart from a 3mm liteply deck.
The dinghy is epoxy resin and microballoons, ths scramble nets are Lego!
Power is again courtesy of Graupner -2, Speed 600 8.4v using lh. and r.h 35mm props. Esc is one of those 50amp ones from the far east. These are far cheaper than the Viper Marine 40 used in my MGB, but slightly heavier and less sensitive at low speeds. Current drain (in the bath!) is up to 30A but this gives a superb on the water pace of an, estimated,8mph. Battery is a 4,600 mAhr NiMh.
(A true scale speed approaching 150mph plus).
I sail it on Ullswater in the Lake district and the Vosper Perkasa type hull shape is superb in the real waves that we get there, flying over the crests and taking aboard No water!
It really looks the part as my photos would show if I could learn how to load more than one! Can anybody help with this?