Just a fun project to use up some old radio gear , single for steering only, or two channel if you want to include a sail winch.
Great for when the pond is full of weed - Also if no wind , stick a motor on the front or back !.
Just have fun !

Model is 49” long and with ballast keel added weighs 17 lbs. hull is covered with 2 layers of 2 oz. cloth fiberglass cloth and painted with Krylon spray can paint. Hitec sail winch servo for main sail and standard servo for jib. Model has auxiliary 6 volt electric power to compincate for my sailing ability’s and wind conditions.
Sails are Mylar.

SPECIFICATION:RG65
Total lenght:650mm
Beam:150mm
Mast height :915mm
Overal height: 1338mm
RTR total weigh:1290g (without 4pcs AA batteries)
Hull material Plastic
Sail material : Mylar

INCLUDED:
*Completed hull with pre applied graphics.
*Two milar film sail sets
*Carbon fiber masts and booms ]2Rigs]
*Zinc alloy ballast and aluminium alloy fin
*Powerful sail winch
*Metal gear rudder servo
*Battery box an On/Off switch for receiver
*AA Nimh batteries 2200mAh for transmitter and
*rc/radio FrskyTaranis 2.4Ghz

Ready go sailing! Added a Robbe sail winch and HS-322HD. Chose not to make a continuous loop for the winch but decided upon a single elastic sheet line which keeps tension on the winch w/o getting twisted up under the spools.

fusion 40 scratch 1/12 scale two motors plus sail winch first sail last sunday 🤔no wind but good for testing not finished yet but well on the way

Here's the photos of the cord coming through the middle of the crane, connected to the sail winch on the bottom end. The bracket to get it to go round 90 degrees had to be modified as it started jamming with no weight on the hook, now a piece of bent tube cut in half as a channel.

I have made the sails & starting to put them on winch servo fitted running line is on it runs around the top of the deck

Kingston mouldings hull will post more pictures as I progress
two more pictures with the sails on they need the running lines to the drum winch then it will be ready to sail

A scratch built model of a Gloucester USA fishing schooner 1900 era. Pine plank on frame, 2 channel radio with a Lego 9volt drive unit as sail winch controlled each way by servo and micro switches, the deck is planked on a thin ply sub-deck and deck openings are sealed with Vaseline. The deep keel slides up into a box through the keel and secured with a bolt.

Scratch built in 2004 from my own plan. Two layers of planks on ply frames, ply deck planked with 3/8 1/16 strips. Length of hull 50" by 13" breath. No motor sail only, winch for main & mizzen, sail arm for fore sails. Featuers a centre plate lowered by gravity and raized be a drum winch, also an expanding rudder, this has two servos to opperate. sails can be reefed or removed depending on weather conditions. Very good sailer Just goes in my car with the top mast & gaff boom lowered.

HI fellow modellers, Another model from the RADMC fleet at the fleetshaven workshop and boat yard in Ponthir.This model was scratch built using a fibre glass hull and plan obtained from a fellow modeller at the Bridgend Show in 2007. The front door and some fittings are made from plastic card and tube, decks are from ply and timber. On board figures are from the pound shop and car boot sales, modified by myself. The on board tank and half truck are RTR models that I have modified their looks to fit into a WWII theme for the craft. This craft has twin drive, 400 motors via 2.5/1 gearboxes. I tend to use both sticks on the TX for drive as this allows me to turn the model on a six pence.The dispatch door works from a rotary pot on the TX and via a rotary sail winch servo in the hull. I have just modified my Planet 5 TX to allow me to change my radio gear in this craft. This model has had meny trips on Cwmbran Boating Lake and at shows the society attend during the year. Still haven't allowed the tank or half track to run off the landing craft up the lake side slipway. one day I might get it on video. Hope you enjoyed the photo's. Regards GreyWolf

Hi" I thought I would put my new rebuild on for all to see ! I found this old Marblehead yacht as a wreck. She was gathering dust in an old reclaim ferniture wherehouse whilst we were on holiday last summer. Been told the yacht had been originaly scratch built in 1950s from a plan. She took me about half a year to rebuild. New parts as follow hiteck sail arm winch with 18lbs of torque. New futaba servo for the rudder. New sails & booms rigs & fittings. New deck made from plank strip wood & varnished. Also finished in painted Ivery white. She sail well in lite to strong winds At my local boating lake at Sheringham Norfolk .
works well on a Spekrum DX5E But can work on any other 2 channal transmitter .
Hope you enjoy the photos .