1959 kit built, restored two years ago,removed the ganette 15cc 4 stroke and replaced it with a bruhless motor which is a EMP 5065 410kv with a 100amp ESC and 4cell 5000 lipo turning a x70 two bladed prop, runs times up to 20 minutes, and a very good but over scale speed, will take a video of her next time a I take her out.
Purchased secondhand, upgraded to a proper motor esc rather than the original/factory on/off micro switch for the motor power. Running a graupner 600 race motor and 7.4 lipo, basically just to run the brushes in on the motor before raising the battery voltage,
bit of a shaky video but try holding the transmitter and filming at same time on your own [ha ha].
it does have the capacity to move a ot faster, but would sooner work the motor in fully first
Hi" to all model boat builders. I thought I would add my new project to this fireboat website for all to see ! I bought this from fleabay as a total wreck. She is a rare Scratch built from a plan of a Walton Thames RAF ASRL launch at 36 inch long & 8 inch wide.took me approx 6 months to do the rebuild. Brush painted with 5 assorted colours with decals working lights ect.
Walton Thames is now running on a new Johnston speed 600 electric motor. 50 amp speed controller 45mm pitched propeller.A 6 volt at4.ah which gives good running time & good scale speed. Photos are taken at Eaton park Norwich England. Enjoy. 😊
My next project will be a 1950s Aerokits/Keilcraft Sea hornet. " So watch this space "
Thank you fellow model boatmen for your kind comments.
on my model boat builds
Yes it would be a very good idea for a build blogg on my next project . 😉 A Prestney
the Lifeboat is looking more and more complete now, deck railings added, pushpit rails on, lifebelts on, deck painted etc. Still loads more to complete yet.
the ACTION sound system is still pulling the crowds every time I switch it on, People passing the pool have to stop and watch it. Ive tried running the Mersey with the sound system off, but naa ! it has to be On , every time [ha ha].
Well you've certainly grabbed my attention, sound ON definately does it for me, my wife said it wasn't a model but a clever photographer using a real boat.ha ha ha.
Keep on sailing your doing a great job.
many thanks for your reply gregg I will take all what you have said onboard I will keep you informed on my success when I get my kit,once again many thanks,please have a look at my 60inch crash tender in the build blog and see what you think not yet been in water yet to try this one out
this hydroplane had to have major work done to strengthen both sponsons internaly as well as filling with expanding foam,this stops it from sinking in the event of a flip over and to put a little weight in the front to help keep the nose down.
fitted a tuned wrap to center pipe,water pump and also added extra fiberglass on the bottom because this was so thin it was flexing at speed and was hitting the bottom of the engine!!!!!. re-painted it too and put my own choice of graphics on.
I fitted the pulse water pump because I wouldn't be running flat out all the time and needed to cool the engine at lower rpm's,and the pulse water pump would do just that with twin inlets and outlets to keep the exhaust and engine head cool.
hI alan,
a pulse pump works off the pressure of the downward stroke of the piston, as the piston moves down pressure builds up in the crankcase bottom and with a small tygon fuel line fitted to the insulator block that the carb sits on you can tap into the 'pulse' of pressure that's created and its this that works a diaphragm inside the pump, it pumps water when your boat is not traveling fast enough to cool itself through the water intakes.
HI bit more deck works done winches crew , that's it for now,
Back on the shelf , to wait for running bits . time to back to trawler build......Larry..
HI " I thought I would put my biggest model from my collection for all to look at ! HMS Avenger took approx 3 years to build . " She is a type 21 frigate at 1/64 scale . At 6 feet long . Scratch built on a fibreglass hull from plywood plastic card & metal parts . Works on a six channel futaba skysport .
Full working red & white leds on deck and cabin , lynxs helicopter with working rotor blades with landing lights. Working radars, bofor gun , A ships whooping sound . Runs on two speed 700 motors off a 12volt gel sell battery which give a good 1hr sailling time . Controlled by a 50 amp speed controller with two brass propshafts behind good size rudders which give a excellant turn .
My model HMS Avenger is a copy from the real ship in which took part in the Falklands war in 1982. Painted in the same grey with a green deck . She looks great on display or on the water . Avenger gets a lot of interest from the general public . please enjoy looking at the photos shown at Sheringham & Eaton park Norwich Norfolk .
" thank you .. A Prestney
Outstanding piece of model building. As a plus it's an unusual subject, not typical of what most folk build. it's too bad these pictures aren't larger, your detail work is exceptional.
Nice to see a scale model of an actual ship. Detail work looks outstanding and I agree with the previous comment re more detailed pics. Seen on the water she looks very realistic. As you have working lights a night time shot would be good 😀
A build blog of your next model would certainly encourage others to get building.
Very well done 😀
HI all, I was given this model in a rather sad state as it had been in a junk box in a farm out-building and had been subjected to the weather from time to time . it had been there for about 20 yrs or more and the balsa hull was 60% rotten . I think it was originally IC powered but had been fitted with a Graupner Jumbo 6v motor and an old style rheostatic sc, ( I did try using the sc but it sucked so much power I gave it a miss - also had no reverse)
Amazingly the motor and sc still worked and with a bit of oil and cleaning the motor is still running well ! I'm using a 1975 Futaba 24v 10A sc and 3cell LiPo which pushes it along nicely. I stripped everything and replaced large bits of the hull, (which was fun as every time you picked it up you would poke another hole in it it was so fragile !) I got it to the stage where it would hang together fairly well and glassed the hull which has made it like the proverbial "brick one". The rest was very careful sanding of the deck and cabin, (they were ply so fared a bit better) and a lot of little filling bits to get it right.
Nav lights and cabin lights all work from the micro switch board, the curtains are left over Graupner Commodore (1975), I've added a mast, new windows,flag pole, cleats, ladder and handrails. Any ideas as to its manufacturer would be great. I have seen another one on our local "Trade Me" web site recently.
Mystery solved,- it's a 'FAIRACRE 11', Modelmaker plan 709 from the late 50s-60s and not a kit as I had assumed. it had obviously been well built by the original modeller.
Aerokit Fireboat 34"
Boat was given to me in poor condition approx 30 years ago, no running gear and most fittings missing or broken, originally powered with IC motor.
I have installed a 43A 700KV Outrunner Brushless motor, Model No : XYH42-50 and a Hobbywing Seaking 60W / Reverse Program Brushless ESC bought from Giantcod, powered by a 3 cell 2200 mAh Lipo battery runtime 15 to 18min, the prop is a 42.5mm 2 blade racing prop. I am well pleased with the performance of the boat.
I belong and sail at the Hartsholme Electric Model Boat Club, Lincoln.
british power boat co. hants and dorset ,range safety launch
hI all here couple of pics of my range saftey launch and british power boat co type 3 hants and dorset 68ft high speed launch. the range safety launch is powered with speed 400 35mm 3 blade prop, 7.2volts 3300mah gives me about 10 mins run time, the hants and dorset as yet not fitted power plant, thinking to go brushles but dont no enough about size to go for yet.
hI there tall paul yes battery was fully charged but I think boat is over propped with 35mm three blades, Im going to try two blade 32.5mm and see if get better duration with same speed
I took advantage of some nice weather to take my Wavemaster out for a spin this afternoon. She's around 58 years old, I bought her from the son of the original builder and have tried to keep it as original as possible so converted from IC to electric, repainted the lower hull, new stainless inner propshaft, made some handrails and fitted the lights. it was very dirty but has cleaned up a treat. I'm running a Darke Horse 700 with a 7.2v 4300Ah battery for these pictures but have the facility to use either one or two sticks, run time today over 30min with some to spare so I'm well pleased! it's a gorgeous classic boat.
Back on the water today @ Crealy, at the same time as testing my 34" Fireboat ( see video ) I gave my 35th scale Vosper ASRL a run so here's a couple more photo's, this time a bit nearer completion. I'll try and upload a video of this later
Regards
Chris
