Brian Clewes has now taken his new scratch built boat on its maiden voyage. The day was fine, if cold, but the wind was just right for the event. The auxiliary motor was used to keep the vessel moving when the wind dropped but she did sail with the little wind present and responded well to the helm. This is Brian's third large scratch built yacht, he is really becoming quite an expert. Also makes his own sails and fittings.
Built this year 2012 by Colin Burrows as a static model. Bought from him to make RC on 2.4. and currently fitted with a 600 motor that is too powerful, advise that was received from a fellow modeller, I am awaiting for a smaller unit to arrive to make it more authentic as it resembles a power boat rather than a trawler. Am also building a speed boat but have put out a request for wiring information as I have already blown up one speed controller!! lol.
I belong to a recently formed club sailing on the lake a Queens Park, Mablethorpe, Lincolnshire. New members would be most welcomed.
Realistic looking model. Low speed high tork motor would suit this. Model Motors Direct do a 555 which is excellent for most scale boats. What ESC are you using?
You can post details of your club in our Model Boat Clubs section, which should help any prospective members find you. 😀
Hi, I am using a Perkins 5510135 Marine 50amp esc and am awaiting a 25mm diam 300rmp motor from Hongkong to replace the Johnson 600 that is already fitted. it's a suck it and see job as I have no experience in the boating field my previous hobby was flying electric planes with lipo's and brushless motors. Going to fit proportional steam simulator, fog horn and whistle, have already fitted sound generator representing the 3 cylinder steam unit that would have been in the real thing. if you have any experience in the electronics field I would welcome help on esc requirement to power twin graupner 700BB Turbo motors.
Just rescued off ebay seller who had it in storage since he inherited it in 1976, it is a Fairey Huntsman, scratch built sometime in early 60's by his father who used to sail it near Manchester. its fitted with a SANWA 2F-2M RC system which seems to be still functioning. I will be doing restoration over the next few months, as there are a few cracks showing along most of the seems and I will need to sand and seal and repaint.
Believed to be scratch built, evidence of old 1 gallon REDEX oil container forming main deck, bits of Mecano used as stiffening and support.
It has a Basset Lowke model 1461/u (motor, stern tube, prop shaft and prop) Set.This dates from the mid 1930's and would have cost 7/- Shillings for those old enough to remember, that would have been abut a day and a half's wages. The photo's show what the motor looked like as it came out and then after cleaning and testing, and yes it runs very smoothly in forward and reverse, from 3 volts up to 12 volts, seems to be quite good at 6, so will probably use when rebuild complete.
As you will see from photo's there is a lot of restoration to do before sailing again.
Now you've stopped laughing, can you identify the type of ship it's meant to be, I thought a Coaster.
Boats name is Who Ha
(Grand children) I'm afraid
Second trip on water in 30yrs plus it's what's known as long build
Upgraded from first sail from 3 blade 9.6v ni-cad to 4 blade 12v ni-mh
Speed and handling are fine for grand children at this time will wind it up at a later date
Another ebay purchase, a Fire Tender which I think is from the 50's. it is fitted with a very unusual old motor with sprung loaded brushes, capacitors, and a fan.... seems to run happily on 12v, which I plan to reinstall. Does anybody recognise it? it was fitted with a 'spring' universal joint. I am fitting a conventional UJ. There is also a circular switch attached to the motor. This appears to be wired to switch in up to 3 battery supplies! but I think I will fit a modern controller with modern nicads.
I sail at the Maldon and Blackwater Model Boat Club at Heybridge.
Regards Frank Burgess
Yes it is...I scratch built it using a GRP 'workboat' hull as a base. I used a simple drawing from the 'Jolie Brise' book blown up to size. I altered the bow, stern and the keel to match the drawing. The rig is slightly undersize and simple the keel is deeper, the deck layout is very approximate taken from photos but simplified to make it more robust for sailing. it has a winch for sail control and the rudder is controlled from the tiller via lines and blocks to a servo under the cabin top.
As you probably know the boat was bought as a Le Havre Pilot boat by EG Martin who then instigated the Fasnet Race, which Jolie Brise won 3 times.
HI Frank I have built model of jolie brise from plans I got from France made few years ago as static model, I have made uo a false keel that I can fit as and when I get round to making sails, have provision for steering via chords running thro the deck in tubes to the steering servo, as yet no thought as to how to install sail winch as have only small openings where hatches fit. you are right about her being pilot cutter and winning fastnet 3 times, she was however built by Monsieur Paumelle in 1913, I hope at some time to get her on the water.
Regards Chiffs
This is my 1/24th scale S80 Schnellboot,it has a Metcalfe GRP hull,the superstructure is a mix of 3mm/4mm ply and 2mm plasticard,it has 3 x Graupner 600FG motors that have a 3.1 ratio gearboxes fitted,the props are 55mm witches hat type,and it has 3 x Electronize 30amp speed cont,it has a really good scale speed running on 2 motors but nearly jumps out of the water when all 3 are engaged,It was scratch built from plans,but not by me,I got it in plain grey,I did the paint job and added the crew,I sail her on a pond near to my home in Edzell,
I have had this boat for about 5 years, so thought that it would like a day out. Sailing at Cwmbran August 2012. its a Billing Polar Trawler, not now made but at about 32 inch long is a managable size. Twin 385 motors 35mm 3 blade brass props. and running on a 7.2 volt 3700 mAh NiMh viper speed controller and a 2.4 Ghz RC it will potter around all morning on one battery. I originally ran it on a 6Volt 4Ah Gel Cell and 27 Mhz setup.
HI Rob if you have an email address that I could use I have photos of the boat, a friend at my club is also restoring one so I have just taken some photos but I could take some more of the areas that you require easily, sadly I do not have a plan myself as my polar was bought on Ebay at least 5 years ago and I had to work from a billing catalogue photo and some photos from old Model Boat Magazines. Hope to hear from you if that will help.
Graham
Thanks so much for getting back my email is PM only - Admin. Any advice or extra pics would be great I really appreciate it. I will upload a pic of the boat at the weekend and show everyone the PROJECT 😯
Launch at last of Coromandel at Cleevedon last week with the help of a passing Portishead/Cleevedon club member who steered the ship, whilst I somewhat did my best with a video camera, I will have to get in a bit more practice.
With the noise from the meccano step down gears it gave a satisfying Impression. I do not expect that it will get sailed much, as it has ended up much more of a display model than something to expose to the sort of water we have around here.
Very realistic looking on the water. What calm conditions you have, my lake usually has a steady swell washing the landing stage from the other side. 😀
Good to see you have finally launched. I know from experience that this often seems to get farther and farther away.
Launch at last of Coromandel at Cleevedon last week with the help of a passing Portishead/Cleevedon club member who steered the ship, whilst I somewhat did my best with a video camera, I will have to get in a bit more practice.
With the noise from the meccano step down gears it gave a satisfying Impression. I do not expect that it will get sailed much, as it has ended up much more of a display model than something to expose to the sort of water we have around here.
This is a scratch built 1;16 fishing/motor sailor from a free plan by james pottinger, made from old teak furniture with mahogany wheelhouse, technobots sound system, 12 volt power shower motor, the original was built by james adams at gourock in 1946 and is still sailing in the western isles of scotland.
