This is GRP hull and a part vac-formed cabin and the rest is scratch build using plastic card! Fittings are from my own range along with the crew. Prop shafts and "A" frames are home made along with the rudders which are to scale form John Lamberts drawings.
Two Groupner eco600 motors are used connected to a 6volt cell lasting around 3 hours running.

Built from Aerokits kit originally but rebuilt/modified many times since then!
Twin 540's (geared) 6V Pb Gel battery for drive. 3 Blade 50mm props (contra rotating) lights (cabin, running Ights and searchlight) on 4.5V Deacs. radar scanner and winch on same supply, radar display screen on a single AA 1.5V.

Fleet Systems radio and speed controllers, Futaba rudders servo, RCME servo driving cam/micro switch unit for lights etc.

Another boat the same as mine seen on a local auction site. Anybody have any ideas as to the manufacturer ?. The dimensions are L 31", W 71/2", H 7" and by the looks of it were Ic powered (or at least mine was and was later changed to electric). Hulls are balsa and planked to 1st 1/4 then finished to the stern with with longer angle cut 'planks'. Cabin top is ply sides with balsa roof and deck is ply and has printed ? planking.
Someone will know but I haven't been able to pin it down to any kit even after going through all my 60s and 70s Model Boat mags.

HI " I thought I would put my biggest model from my collection for all to look at ! HMS Avenger took approx 3 years to build . " She is a type 21 frigate at 1/64 scale . At 6 feet long . Scratch built on a fibreglass hull from plywood plastic card & metal parts . Works on a six channel futaba skysport .
Full working red & white leds on deck and cabin , lynxs helicopter with working rotor blades with landing lights. Working radars, bofor gun , A ships whooping sound . Runs on two speed 700 motors off a 12volt gel sell battery which give a good 1hr sailling time . Controlled by a 50 amp speed controller with two brass propshafts behind good size rudders which give a excellant turn .
My model HMS Avenger is a copy from the real ship in which took part in the Falklands war in 1982. Painted in the same grey with a green deck . She looks great on display or on the water . Avenger gets a lot of interest from the general public . please enjoy looking at the photos shown at Sheringham & Eaton park Norwich Norfolk .
" thank you .. A Prestney

HI all, I was given this model in a rather sad state as it had been in a junk box in a farm out-building and had been subjected to the weather from time to time . it had been there for about 20 yrs or more and the balsa hull was 60% rotten . I think it was originally IC powered but had been fitted with a Graupner Jumbo 6v motor and an old style rheostatic sc, ( I did try using the sc but it sucked so much power I gave it a miss - also had no reverse)
Amazingly the motor and sc still worked and with a bit of oil and cleaning the motor is still running well ! I'm using a 1975 Futaba 24v 10A sc and 3cell LiPo which pushes it along nicely. I stripped everything and replaced large bits of the hull, (which was fun as every time you picked it up you would poke another hole in it it was so fragile !) I got it to the stage where it would hang together fairly well and glassed the hull which has made it like the proverbial "brick one". The rest was very careful sanding of the deck and cabin, (they were ply so fared a bit better) and a lot of little filling bits to get it right.
Nav lights and cabin lights all work from the micro switch board, the curtains are left over Graupner Commodore (1975), I've added a mast, new windows,flag pole, cleats, ladder and handrails. Any ideas as to its manufacturer would be great. I have seen another one on our local "Trade Me" web site recently.

1. The sorry state of the Hull on the Fire Boat. Purchased from Ebay about 6 months ago, only now just started working on refurbishing it, it was covered in car body filler.

2. After about 2 weeks of very hard work it looks much better. it is running on a Johnson 600 size motor and 6v Gel Battery for its first sail at the Cwmbran Model Society tomorrow, so I hope that is will be OK. it does not appear to be an Aeroits model as the cabins remove from the hull. Not just the Cabin tops. I will try and supply some action photo's later.

Hello Bob ,Finally got started on the fireboat. Have stripped all the paint and varnish from the deck up and also inside the hull. Now have separated all the cabin roofing and upper bulkheads for access to the keel which has delaminated in places. The complete shaft just pulled out of the hull, the glue had no adhesion at all and a new oil fed shaft will be fitted. The next job will be to strip the paint on the hull, check it out and glass laminate it. More photos soon. Regards Graeme.....

the sea rover was bought locally as a wreck with much of the forward section of the cabin missing , however it has been rebuilt in a matter of weeks to sailing condition , its now running a single vision 600 motor on 7.2 volts , & has a reasonable turn of speed and very good rudder response ! the fpl was a double purchase as I bought a pair of hulls , one had a better finish than its sister although this didnt matter as they were both stripped back to bare timber and resprayed with wilkinsons enamel spray . as the cabins were not remaining Ive made both boats into vospers mk2 range safety launches , neither models are fully finished but Ive started to use 1640 , I know 1646 wasnt a number issued by the raf , but as the model is to be operated by my neice it was the number she has chosen !

My Sun Tug MK25 version, originally adapted from a Lesro Sun Tug Kit, actually still being built [not quite yet complete] but seaworthy enough to get some testing time in the water. it has more than enough power to haul my dusseldorf along when the batteries are flat after some time sailing, so rather than pull the fireboat out, decided to let the tug do some work.
Powered by a hectoperm motor with 3:1 gearbox,twin 6v gel batteries,water pump to operate the fire monitors,engine sound, nav lights, interior lights [cabins] rotating radar scanner,

HI Dave. Here are a few pics. of the cabin and rear deck. I have no idea if they are correct as I have been unable to get a copy of the original drawings. The cabin top fits into a coaming / channel and is held in place by a rubber band, you can probably see the hooks in the photos. The rear deck sits on a ledge. it does not appear to be very watertight but seems to work quite well. Hope this helps. - John

Can anyone tell me what boat this is?
I think its a modified Aerokits fire boat or Sea queen,
The deck is different because it steps down, the cabin looks to be modified, the hull is all fibre glass with wooden bulkheads.
Nice 10cc Merco engine.
Will upload more recent pics as the pics are from about 18 months ago, I've since started re building the boat to sail then in future sell.

Aerokits Solent Kit bought as a present in the 70's. Worked on it on and off until 2000 when I finally made a maiden voyage. Two Buhler motors driving Prop Shop props with Bobs board and 12v 17Ah SLA. Radar works. Realistic scale speed and looks great on the water. To turn I have used micro switches to cut out one motor on full rudder. The large keel was causing the model to cease turning with both props turning. I sail with Crewe MBC at Boundary Park Lake. Oct 09. Have now found out that the cabin door on my model was only fitted to the last three builds 48-014,-015 and -016. At least I can give her a name once I have decided which to use.