Predator Outrigger MK1
Scratch built outrigger hydro with a 3600KV motor ESC and a 11.1v 45C 5000mAh battery, running an Octura X435 prop
Photos & videos
Showing results for “battery”
· Clear search
Search results
155 posts · Page 10 of 13
Predator Outrigger MK1 Outrigger Hydro
Built from a .PDF plan I found on the net, this 22" Outrigger Hydro sports a Hobbywing 3600Kv Brushless, along with a Hobbywing 60A esc, a 5000mAh 11.1v 45C LiPo, and an Octura X435 Prop connected to a Strudder from Prestwich models.. it weighs 930g without the battery, with the battery, she goes 1386g.
This was it's Maiden run, at Herbert Woods Boatyard, at Potter Heigham Norfolk. it ran very nicely, but can do with a little tweaking to get more speed.
For the record, I did not swear, it was someone onlooking.
This was it's Maiden run, at Herbert Woods Boatyard, at Potter Heigham Norfolk. it ran very nicely, but can do with a little tweaking to get more speed.
For the record, I did not swear, it was someone onlooking.
2 comments
- aquamatic80Petty Officer 2nd ClassI have not played with the prop depth and angle yet, however, she has been banished to the back of the cupboard to make way for the MK2, to be re-visited a later date.
Predator outrigger Mk1
Built from a .PDF plan I found on the net, this 22" Outrigger Hydro sports a Hobbywing 3600Kv Brushless, along with a Hobbywing 60A esc, a 5000mAh 11.1v 45C LiPo, and an Octura X435 Prop connected to a Struuder from Prestwich models.. it weighs 930g without the battery, with the battery, she goes 1386g.
1 / 4
aeromarine apache 50
my boat is powered by a 26cc zenoah engine,I skinned the outside in real carbon fiber and the interior with carbon/kevlar.I use a spektrum DX3S 2.4ghz tx with a spektrum MR3000 marine rx.the boat is equipped with a killer bee remote kill switch that doesn't need any power source to work so it will still kill the engine instantly in the event of battery failure or broken wire or when I want to from the tx. the carbon fiber was hand laid and wetted out with a special resin,then around six weeks of hand sanding with different grades of wet and dry to get it super smooth,then polish.
4 comments
- johnfastboatAble SeamanI'm familiar with the 26cc Zenoah and the syle of Offshore boat you have produced with its unique finish. I'll look forward to an on-water shot. Thanks for the looksee. John: 👽
1 / 2
Griffon 2000 TD
Built from light ply and balsa from a plan available on the Model Hovercraft Association website (under resources) www.modelhover.org it is powered by two 540 brushed motors with dedicated speed controllers.
This model has now been sold and replaced with a newly built Canadian Coastguard Griffon 2000TD built off a Mark Porter plan but using two Graupner Speed 600 motors, one powered by a 3000 Li-Po battery for thrust and the other on a 7.2v Ni-Cad for lift.
This model has now been sold and replaced with a newly built Canadian Coastguard Griffon 2000TD built off a Mark Porter plan but using two Graupner Speed 600 motors, one powered by a 3000 Li-Po battery for thrust and the other on a 7.2v Ni-Cad for lift.
2 comments
- Chris BLeading SeamanI have just got the plans to build this from MHA
Any info you have on your build, would be much Appreciated
good looking model by the way 😊Liked by Skydive130
RNLB Rosemary Shaw
Built from Aerokits kit originally but rebuilt/modified many times since then!
Twin 540's (geared) 6V Pb Gel battery for drive. 3 Blade 50mm props (contra rotating) lights (cabin, running Ights and searchlight) on 4.5V Deacs. radar scanner and winch on same supply, radar display screen on a single AA 1.5V.
Fleet Systems radio and speed controllers, Futaba rudders servo, RCME servo driving cam/micro switch unit for lights etc.
Twin 540's (geared) 6V Pb Gel battery for drive. 3 Blade 50mm props (contra rotating) lights (cabin, running Ights and searchlight) on 4.5V Deacs. radar scanner and winch on same supply, radar display screen on a single AA 1.5V.
Fleet Systems radio and speed controllers, Futaba rudders servo, RCME servo driving cam/micro switch unit for lights etc.
3 comments
- larryshaw48Able SeamanThanks for that! She's crossed the Blackwater estuary from South to North but never made Norfolk yet!
- aprestneyLeading SeamanHi" I am very lucky to have a nice local pond at Sheringham for sailling. But it do get very busy in the summer with holiday makers during the days .But I chose to take my model up for sailling with the older boys in the long summer evenings or Sunday mornings. I occasionaly sail at the megga big lake at Eaton park Norwich. There is a club meet up there every weekend. With events on though the summer months . I talk to a lot model boat enthusiasts from all over the country so you are welcome to join us here for a sail . 🙏 APrestney
1 / 4
Egret- A Vic Smeed Silver Mist
This boat was built from Vic Smeed's Silver Mist design, from the fifties I think. The boat is 36'' long by 9''. it is planked in obeche on 6mm birch ply frames with solid blocks for the bow and lower stern sections, epoxied on the inside. it is powered by an MFA geared 500 motor- 2.5:1 I think with a 7.2v NIMH battery. There were one or two details to complete when these photos were taken at Crealy in Exeter- there still are to be honest! I thought I'd add this in as I'm so Impressed with the look of this new site.
Liked by jbkiwi and Brightwork
5 comments
1 / 4
HMS Avenger type 21 frigate
HI " I thought I would put my biggest model from my collection for all to look at ! HMS Avenger took approx 3 years to build . " She is a type 21 frigate at 1/64 scale . At 6 feet long . Scratch built on a fibreglass hull from plywood plastic card & metal parts . Works on a six channel futaba skysport .
Full working red & white leds on deck and cabin , lynxs helicopter with working rotor blades with landing lights. Working radars, bofor gun , A ships whooping sound . Runs on two speed 700 motors off a 12volt gel sell battery which give a good 1hr sailling time . Controlled by a 50 amp speed controller with two brass propshafts behind good size rudders which give a excellant turn .
My model HMS Avenger is a copy from the real ship in which took part in the Falklands war in 1982. Painted in the same grey with a green deck . She looks great on display or on the water . Avenger gets a lot of interest from the general public . please enjoy looking at the photos shown at Sheringham & Eaton park Norwich Norfolk .
" thank you .. A Prestney
Full working red & white leds on deck and cabin , lynxs helicopter with working rotor blades with landing lights. Working radars, bofor gun , A ships whooping sound . Runs on two speed 700 motors off a 12volt gel sell battery which give a good 1hr sailling time . Controlled by a 50 amp speed controller with two brass propshafts behind good size rudders which give a excellant turn .
My model HMS Avenger is a copy from the real ship in which took part in the Falklands war in 1982. Painted in the same grey with a green deck . She looks great on display or on the water . Avenger gets a lot of interest from the general public . please enjoy looking at the photos shown at Sheringham & Eaton park Norwich Norfolk .
" thank you .. A Prestney
2 comments
- rustypistonLeading SeamanOutstanding piece of model building. As a plus it's an unusual subject, not typical of what most folk build. it's too bad these pictures aren't larger, your detail work is exceptional.
- Dave MVice AdmiralNice to see a scale model of an actual ship. Detail work looks outstanding and I agree with the previous comment re more detailed pics. Seen on the water she looks very realistic. As you have working lights a night time shot would be good 😀
A build blog of your next model would certainly encourage others to get building.
Very well done 😀
1 / 4
RAF Air Sea Rescue Launch 2507
HI Fellow Enthusiasts
These pictures show my scratch built RAF Air Sea Rescue launch 2507. it was built using my own scaled up planes over the period July 2006 to August 2008. its approx. 4 feet long by 11 inch wide and stands 24 inch high.
The boat has twin Johnson brushed electric drives via 2.5/1 reduction gearboxes with three bladed 40 mm brass props. The speed controllers being 15 amp Electronize supplied from 4.5 amp D cells made into a 12 volt battery pack.
The boat sound system consists of a Diesel sound generator and machine guns being fired by an electronic ring counter circuit that allows the guns to fire individually or together depending on their selection via a diode network. The unit is switched on and off via a Electonize switch unit that also switches the boats lighting system on and off.
All the special fixtures required for this model being self made this includes the figures found on and in the boat. The basic figures are usually obtained from car boot sales or the local ÂA£ shop for next to nothing and then modified to the model boats requirements.
Launch 2507 was commanded by F/O W. Garret who reputedly made the most northerly pick up on the 26th June 1944 for the crew of a downed Catalina, for this action he was awarded a M.B.E. The Catalina pilot F/Lt. Horner R.C.A.F. died of exposure and was awarded a posthumous V.C.
I hope you enjoyed the pics and information.
Regards
GreyWolf
These pictures show my scratch built RAF Air Sea Rescue launch 2507. it was built using my own scaled up planes over the period July 2006 to August 2008. its approx. 4 feet long by 11 inch wide and stands 24 inch high.
The boat has twin Johnson brushed electric drives via 2.5/1 reduction gearboxes with three bladed 40 mm brass props. The speed controllers being 15 amp Electronize supplied from 4.5 amp D cells made into a 12 volt battery pack.
The boat sound system consists of a Diesel sound generator and machine guns being fired by an electronic ring counter circuit that allows the guns to fire individually or together depending on their selection via a diode network. The unit is switched on and off via a Electonize switch unit that also switches the boats lighting system on and off.
All the special fixtures required for this model being self made this includes the figures found on and in the boat. The basic figures are usually obtained from car boot sales or the local ÂA£ shop for next to nothing and then modified to the model boats requirements.
Launch 2507 was commanded by F/O W. Garret who reputedly made the most northerly pick up on the 26th June 1944 for the crew of a downed Catalina, for this action he was awarded a M.B.E. The Catalina pilot F/Lt. Horner R.C.A.F. died of exposure and was awarded a posthumous V.C.
I hope you enjoyed the pics and information.
Regards
GreyWolf
12 comments
- TaffWhittleRecruitMany many thanks for your most welcome Pictures and the very welcome advice ,I started this time last year2011 and then found out I was 4inches short for one sixteenth and having built the hull abanded it and never got started again. Built I'm trying to start now but I'm having problems with my computer, need to sort that out first. But I've been down abit too and your kind letter to me has bucked me up too. I've seen the films and get them up on the computer now and then. I've corrected my plans for one sixteenth and I've also started on a set of Plans to make a one sixteenth Whaleback as per the Airfix model, only I was thinking of it when the local Paper had an articule about a local man's Granddaughter did a project for WW2 in her school across the road from where we live and her teacher aproched her Mum about this project and found out that her Dad had written his life on Whaleback's in the North Sea and English Channel and it had been in her loft for sometime So the teacher asked if she could get it published which she did and the process went to re-roof the school, I've forgotten the name but when I find it I will let you know. But many many thanks for geeing me up and just feeling sory in general Thanks "Grey Wolf" 😟 👋
- TaffWhittleRecruitHI Grey Wolf again I've remembered the book only a small one but a good real story "Percy's Piece of the War"
1 / 4
Aerokits sea nymph
Welcome all fellow model makers .
Here is restored 1950s Aerokits wreck which was picked up at a antiques fair . She is running on MFA torpedo 500 motor & 7.2 volts 4600 nimh Battery which should make her get up and go !! The other small boat is a Aerokits 1950s fasts patrol which will be the next restored model .
Here is restored 1950s Aerokits wreck which was picked up at a antiques fair . She is running on MFA torpedo 500 motor & 7.2 volts 4600 nimh Battery which should make her get up and go !! The other small boat is a Aerokits 1950s fasts patrol which will be the next restored model .
Liked by jacko and circle43nautical
7 comments
- jelley_babyChief Petty Officer 1st ClassMany thanks have found a plan, now I know what it is, and can start finishing the boat, mine was just a frame bought some time ago on an Auction Site E---. Making up the missing bits will be interesting. Graham (jelley_baby)
- jelley_babyChief Petty Officer 1st ClassHI Last year you helped me identify an Aerokits Fast Patrol Boat, of wihich I only had the basic frame I have now found time to finish it, the results are in the sites Boat Build Blog under Aerokits Fast Patrol Boat. Thanks again for your original information. Graham (jelley_baby) 😊
1 / 4
Restored Fireboat
Aerokit Fireboat 34"
Boat was given to me in poor condition approx 30 years ago, no running gear and most fittings missing or broken, originally powered with IC motor.
I have installed a 43A 700KV Outrunner Brushless motor, Model No : XYH42-50 and a Hobbywing Seaking 60W / Reverse Program Brushless ESC bought from Giantcod, powered by a 3 cell 2200 mAh Lipo battery runtime 15 to 18min, the prop is a 42.5mm 2 blade racing prop. I am well pleased with the performance of the boat.
I belong and sail at the Hartsholme Electric Model Boat Club, Lincoln.
Boat was given to me in poor condition approx 30 years ago, no running gear and most fittings missing or broken, originally powered with IC motor.
I have installed a 43A 700KV Outrunner Brushless motor, Model No : XYH42-50 and a Hobbywing Seaking 60W / Reverse Program Brushless ESC bought from Giantcod, powered by a 3 cell 2200 mAh Lipo battery runtime 15 to 18min, the prop is a 42.5mm 2 blade racing prop. I am well pleased with the performance of the boat.
I belong and sail at the Hartsholme Electric Model Boat Club, Lincoln.
Liked by doghouse and circle43nautical
1 / 4
The Scout
Kit by Metcalf Mouldings, Waveney Lifeboat, figures by speedline, running with 2x 850 Motors,12volt sla battery, speed control by a Action P94 set to tank steering.