The boat is a scratch built and started life in the shed. it is a semiscale model at aprox 36inch, built with balsa wood.It is full remote control and fitted with two Mtroniks Vision 600 motors one 12volt 7ah battery,one seasprint esc.
It was built as a fun boat so I could sail with my friend Peter thomas with his variuos boats.
Several things have now been added since this boat was first built, IE smoking stacks, fireing torpedoes and magnetic pickups for colecting them. Also has working radar/moving gun + a home built bec.
Flag poles and flags/compas has been added on the superstructure.
Each motor draws 6amps at full power, I have measured the speed from one point to another at a spacing of 60mtrs, and timed at 15 seconds, but this is a bit fast for this boat as she starts to plane out of the water.
We sail her at New Brighton lake on the wirral most wednesdays. As the weather is now a bit cool I have just purchased a simular model to this at 1:48 scale 110ft island class USCG Patrol boat so I can look at them both in action when the weather picks up. Anyone wanting info can contact me via this website.

This is one of the Aerokits models, however it has recently been stripped down to the wood to apply a fibreglass coating.

These video clips show the boat undergoing trials before being completly re-fitted.

puffer scratch built made from old wardobe plywood
for the frames then plated up in thin ply like it would be when built looks nice in the water.

puffer scratch built made from old wardobe plywood
for the frames then plated up in thin ply like it would be when built looks nice in the water.

My Dad built this Fireboat 40 years ago, following the Practical Electronics magazine article. I watched as he built the plywood boat then built the discrete electronics; it was full of batteries but was great fun. I later fitted the 2-channel radio and then dad repainted it blue? its now time to give it some TLC and get it back as it should be.

Scratch built SDM MkII tug 1/48 scale.

Hull started out as polystyrene foam and plywood. Started July 29,2006 and in the water by Aug. 11th for sea trials. Detailed over the following 18 months.

The model is powered by 12vdc using Graupner Speed400-2.33:1 gear drive, and the small Graupner Schottel drives #1761. Separate ESC and Steering control for each drive.

The Lighting is 3mm LED cast into clear, or tinted, polyurethane lamps.

It sails the Pacific Northwest, USA, homeport Portland, Oregon.

This lifeboat was a part-kit from Metcalfe Mouldings, being just a bare hull and superstructure. All the detailed work was scratch- built by my son and I did all the drive and electrics.

It is powered by two 540 motors through a single water-cooled speed controller and the props are about 35mm. My son and I sail it at our club water at Knightcote in Warwickshire. it is now about 4 years old and, (touch wood), pretty reliable.

This is my ** version of the Sea Queen. My father owns one of the originals and when one lunch time I saw one on the ** web site I knew I had to get one.
It was to be a winter build project and work started in the autumn of 2006 and it was launched in May 2007. I was very disappointed to see the all white paint finish used on the ** advertisements and decided I was going to re-create the look of the original. Cosmetically the big problem was that the original used mahogany finish ply for the cabin sides and the ** version was just plain birch. However after a bit of staining I was quite happy with the finished colour. This was contrasted against clear coated lime wood deck planking.
Also ***a€™s bag of fittings missed out on the signature life belts so I had to make my own.

One Improvement that I did make was the inclusion of a dashboard, instrument panel and throttle slide.

The graphic on the transom was a custom cut from callie-graphics.

The supplied motor was replaced with an MFA Torpedo 850 which is a direct replacement. ( Same mount, same screw fixing centres etc ).
Battery is a 12V 7A gel cell, ESC is an Mtronics Marine Viper 40A

46 inch Crash Tender rescued from E-bay. Currently in the process of total restoration and have had to scratch build the entire super structure. Have fitted a Merco 61 engine with tuned pipe (the noise is awesome).

Have gone for it with the radio control- - employing a Robbe F14 plus an extra 8 channel module with decoder. So far extra controls are : each monitor (scratch built using brass pipe & sheet) left & right (using Robbe pulley set to give me 270 degrees travel), two Irvine water pumps, (real car) hooter, winch (using gearbox from Maplins) and movement for jib and search light.

I sail at Brentwood in Essex - where you can still run IC boats.