HI fellow model leers.this is my latest model.Built in 1926' for the Ffyfe(bananas) family. Originally it was run on steam,but in 1939 converted to diesel,this was kept until 1957 when all the staterooms were replaced by cargo holds . She was then made into a feeder bringing eleven thousand boxes from Rotterdam to Southampton. She was scrapped in the seventies.my model of her was from 1926 the scale is approx 1/30th her length is 48 inches including bowsprit, and has a beam of 10 inch amidships. She is totally scratch built, plank on frame, all the decks are individually planked with black card in between , wheel house and all other parts are mahogany. She runs on a decaperm geared motor @ 6 volts, and the lighting system consists of 10 accommodation lights, port and starboard , wheelhouse, and both mast headlights,the large saloon skylight is also lit up with a set of disco lights on a separate circuit. The funnel houses a heavy duty smoke unit switched on by switching unit.

This is a scratch built 1;16 fishing/motor sailor from a free plan by james pottinger, made from old teak furniture with mahogany wheelhouse, technobots sound system, 12 volt power shower motor, the original was built by james adams at gourock in 1946 and is still sailing in the western isles of scotland.

Hi" All . Thought I would put some photos of my last winter project for all to see ! This model took approx 3 month to rebuild from an ebay wreck . A 1980s lesro Stiletto speed boat kit.A total rebuild was needed . Siletto running set up is a Johnston air cooled speed 600 electric motor. 50 amp speed contoller 7.2 volt at4600mh power pack which will lift her out of the water at very good speed. Siletto is finished of in dark mahogany stripwood vinneer & Ivery white / post box red .I do think the older colours look better on the older models . I sail my boats at Sheringham Norfolk
enjoy the photos . From A prestney

I have admired this design for many years, along with a lot of Vic Smeed's drawings.
This model is enlarged by 1.7 giving a length of 36'' and a scale of 1:16. The finished boat weighs about 15 1/2lbs and is powered by an MFA 919D 540 with 2.5:1 reduction, using an Mtroniks ESC and Planet 2.4ghz radio.
The hull was planked in obeche on 6mm ply keel and frames with mahogany blocks at bow and stern. The photos were taken on her maiden voyage at Crealy in Exeter.

This boat was scratch built from Harold Underhill plans, available still from Brown,Son and Ferguson. The hull was mahogany on 6mm ply frames. The engine was a Caton from Maxwell Hemmens supplied bya gas-fired Cheddar Puffin boiler. The propeller was a two inch four bladed brass job from Rivabo I think. The displacement of the boat is 25lb- a bit of a lump to carry to the water but it does work well once in the water. She has now been converted to electric using a MFA geared 540 type motor witha 7.5ah lead acid gel cell. Looking again at this video I begin to wish I had left it as steam but there is something to be said for 'switch on and go'.
I started building the boat in the mid nineties and it has now had a repaint- it always been a favourite. This video was taken in the early noughties at Crealy in Exeter.

This is my Sea Hornet which was rescued from Ebay see photo 1. Gray (Froggyt996) recognised it as a Sea Hornet even with the hideous cabin attched which the prvious owner had made. Also see the propshaft angle in photo 1 - would this have ever worked? Gray again restored this for me, I wanted a mahogany boat which looked like an italian speedboat and this is what he did for me see photo 2. Photo 3 sees the Sea Hornet on the sea at Southsea just after the start of the Round Britain Race in 2008. The receiver battery failed and a very nice Lifeboat Man from Southsea happened to be watching me run the boat and rescued it when it stopped running. it was put in dry dock over this winter to be tidied up again after a couple of years constant use and photo 4 sees it with its 2 new screens, re-varnished and 2 new rubbing strake. it is powered by 2 Graupner Speed 600 motors, a Ripmax sea sprint watercooled speed controller and 2 x 3 blade prop shop props on 2 x light weight shafts. it is also filled with bouyancy foam it case the inevitable happens which makes it quite heavy. it is ran on 2 x 8.4 volts nicad sticks and gives me a running time of approx. 20 minutes with quite a good turn of speed.
Marie (alias Mrs Froggyt996)

This is my ** version of the Sea Queen. My father owns one of the originals and when one lunch time I saw one on the ** web site I knew I had to get one.
It was to be a winter build project and work started in the autumn of 2006 and it was launched in May 2007. I was very disappointed to see the all white paint finish used on the ** advertisements and decided I was going to re-create the look of the original. Cosmetically the big problem was that the original used mahogany finish ply for the cabin sides and the ** version was just plain birch. However after a bit of staining I was quite happy with the finished colour. This was contrasted against clear coated lime wood deck planking.
Also ***a€™s bag of fittings missed out on the signature life belts so I had to make my own.

One Improvement that I did make was the inclusion of a dashboard, instrument panel and throttle slide.

The graphic on the transom was a custom cut from callie-graphics.

The supplied motor was replaced with an MFA Torpedo 850 which is a direct replacement. ( Same mount, same screw fixing centres etc ).
Battery is a 12V 7A gel cell, ESC is an Mtronics Marine Viper 40A