It is a Sirmar limited edition (100) semI kit at 1/48 scale and some 6 feet in length. When he bought the model it was already constructed, but as a static model. So out came the jigsaw, Manual NOT powered.
The deck around the aft gun turret was cut to allow a good inspection of the inside of the hull. He tried to remove the bridge superstructure but this would have meant destroying it to remove. Out came the jigsaw again and cut an access hatch in the main deck.
The steering servo was fitted and attached ( by keyhole surgery ) and 2 x MFA 800 motors were fitted. Scale Prop Shop Props were fitted and the radio gear just jury rigged for her first trial. She was roughly ballasted with 2 x 12volt 7Ah batteries and she was ready for her first trials.
She sailed well with no water ingress to the hull, so the radio gear was installed properly with individual speed controllers to each motor. The results are as seen here.
This lifeboat was a part-kit from Metcalfe Mouldings, being just a bare hull and superstructure. All the detailed work was scratch- built by my son and I did all the drive and electrics.
It is powered by two 540 motors through a single water-cooled speed controller and the props are about 35mm. My son and I sail it at our club water at Knightcote in Warwickshire. it is now about 4 years old and, (touch wood), pretty reliable.
This was given to me by the Minoros Family from Sutton in Surrey found in a loft after the death of a family member it is 46" long with a beam of 15" and I guess built in the early 1960's.
I think it has been scrach built, but is a copy of the kit above, it has a large petrol engine but I have no idea what cc it is. I would be greatful for any help or suggestions as I require some parts to finish restoring it. and converting it to an electric Motor drive
The Sea Queen is an original Aerokits kit from the early 1960's. it was built by my Dad in the early 1960's. it was originally fitted with an ED Seaotter, next it had a Channel island Special, then a 15cc Gannett and finally fitted with the OS 80 which it still has fitted today.
I sail at King Lear Lake at Watermead County Park in Wanlip Leicestershire. it sat in my attic for 22 years and 2 years ago I dragged it out and gave it a bit of TLC and started to use it again and it has been ran most weekends for the last 2 years.
I ran this boat virtually all day of the Burton Model Boat Club's Fireboat day in September 2006. it is currently in dry dock having a full de-barnacle and repaint.
"BOO BOO Kitty" is a scale model of a Crosby designed Cape Cod Cat Boat.[USA] it was built from scratch at a scale of 9.04" = 1"; the model being 26.5" oal.
The dimensions were taken from a book that highly detailed the building of a real Cat Boat.
The hull is plank-on-frame with epoxy and glass cloth as the final surface. A separate and detachable fin keel was used for sailing of the centerboard model.
Radio controls were a Hitec sail winch [HS-785HB] and one servo for the rudder with a 2 channel JR transmitter.
Copying the book plans, scaling them down, and construction took up the winter of 2006/2007. The model is sailing better than anticipated on a local lake in Langhorne, Pennsylvania.
These pictures are of a scale model of Captain Joshua Slocum's "Spray". it was sailed around the world, singlehanded between 1895-1898. Slocum re-built a Delaware oysterman hull in Fairhaven, MA and had been a gift to him.
After reading of his exploits in an original copy of his book, 'Sailing Alone Around The World' 1899 The Century Co., John copied the drawings that were in the book, established a scale for each and then converted those scales to just one - 1"=14.6" and proceeded to make a model of the famous boat. At that time [2003-2004] there was a commercial kit available but after much research John concluded that he had enough information from the book to build his own version. Actually the available kit contained some mis-information about the boat and that settled the matter.
The model was built plank-on-frame and then covered with epoxy/glass since it was intended for RC. He sailed her during the summer of 2004 and was quite pleased with her performance. An opportunity to sell the model came to him and he did so in January 2005.
I am working on my crash tender--originally bought when I was eleven. I see people have similar experiences.Never had it being powered BUT it floats and have an Enya glow installed. Now in Qld Australia, however started it in Yorkshire.
Aerokits Boats built by Christian Sheppard-Capurro
This is an Aerokits 34" built over 20 years ago and runs an Enya glow engine with Futaba 2-ch radio (upgraded from 1 ch). All fittings were built from scratch.
The second boat is also from the 34" kit, re-cut into a Hants & Dorset RAF HSL. Also powered by Enya.
The third boat used to be an Aerokits Sea Commander, converted into RAF 63ft Pinnace.Powered by an ancient diesel.
The fourth boat is an Aerokits Swordsman flat out in the Bay Of Gibraltar. Big Enya!
