This is my 1/24th scale S80 Schnellboot,it has a Metcalfe GRP hull,the superstructure is a mix of 3mm/4mm ply and 2mm plasticard,it has 3 x Graupner 600FG motors that have a 3.1 ratio gearboxes fitted,the props are 55mm witches hat type,and it has 3 x Electronize 30amp speed cont,it has a really good scale speed running on 2 motors but nearly jumps out of the water when all 3 are engaged,It was scratch built from plans,but not by me,I got it in plain grey,I did the paint job and added the crew,I sail her on a pond near to my home in Edzell,

HI bit more deck works done winches crew , that's it for now,
Back on the shelf , to wait for running bits . time to back to trawler build......Larry..

This is GRP hull and a part vac-formed cabin and the rest is scratch build using plastic card! Fittings are from my own range along with the crew. Prop shafts and "A" frames are home made along with the rudders which are to scale form John Lamberts drawings.
Two Groupner eco600 motors are used connected to a 6volt cell lasting around 3 hours running.

whilst being off work with cancer have spent three months building my polar trawler which I had to remake a lot of superstructure with plasticard due to the old ply delaminated. it has twin screws powered by two 400 motors and 40 amp esc and 6v sla. I think she looks quite good

HI Fellow enthusiasts
The first photo shows the boat as it was bought from an E Bay auction in late February for the price of 14.50, for that price I had to bid on it, even thought I had a new kit of the same model on order from a model shop from the end of December, before VAT went up. The models turned out to be the 4 feet versions some 11 inch wide and now is about 19 inch high. This model turned up several days before the new kit turned up, and was a bit worse for ware than anticipated as the deck had started to part company from the hull. After stripping the deck of all remaining deck furniture the deck was re laminated to the hull, prop shafts and rudder tubes also refitted using plenty of resin and cloth. A rubbing strip was fitted around the deck hull line to tidy up the visible damage. When I was happy with repairs the hull and deck was rubbed down and sprayed. Using the information in the new kit and some photos of actual boats, MJB's (My junk boxes) supplied all the required parts to scratch build 90% of the models fittings as seen, this includes the figures on the deck. These being obtained off an EBay site as 1/24 unpainted train scene figures that required some or may be a lot of adjustments to their appearance. Several items have still to be made and fitted. As I'm working on her sister boat P147, will make extra parts in one go.
The boat has twin electric drives, the motors, MFA 919D series, are fitted with their own 2.5/1 gearboxes and they drive 40 mm three bladed conta rotating brass props. They have independent 15 amp Electonize speed controllers run from two 7.2 volt packs in series. The switching arrangements for lighting has still to be finished off. Don't know if I'll fit a sound system as the boat is for my grandson.
The boat has had several trips on the Society's water at Cwmbran with myself and my grandson at the helm. it seems to go fast enough for him. (The new boat P147 has been built with triple screws.) Can't wait to see both models on the water together.
Hope you have enjoyed the pictures and information.
Regards
GreyWolf

HI Fellow Enthusiasts
These pictures show my scratch built RAF Air Sea Rescue launch 2507. it was built using my own scaled up planes over the period July 2006 to August 2008. its approx. 4 feet long by 11 inch wide and stands 24 inch high.
The boat has twin Johnson brushed electric drives via 2.5/1 reduction gearboxes with three bladed 40 mm brass props. The speed controllers being 15 amp Electronize supplied from 4.5 amp D cells made into a 12 volt battery pack.
The boat sound system consists of a Diesel sound generator and machine guns being fired by an electronic ring counter circuit that allows the guns to fire individually or together depending on their selection via a diode network. The unit is switched on and off via a Electonize switch unit that also switches the boats lighting system on and off.
All the special fixtures required for this model being self made this includes the figures found on and in the boat. The basic figures are usually obtained from car boot sales or the local ÂA£ shop for next to nothing and then modified to the model boats requirements.
Launch 2507 was commanded by F/O W. Garret who reputedly made the most northerly pick up on the 26th June 1944 for the crew of a downed Catalina, for this action he was awarded a M.B.E. The Catalina pilot F/Lt. Horner R.C.A.F. died of exposure and was awarded a posthumous V.C.
I hope you enjoyed the pics and information.
Regards
GreyWolf

Ahoy
this model dont need any introduction because there are thousands upon thousands of these kits were produced and even being produce as I post this this build. I purchased this kit when it was first released in 1963. there was a discount store that sold anything from appliances to plastic models. I went in there one day to see what they have, there to my delight and surprise there was a stock table that must have had atleased a 100 or more of these kits they were sold for $11.95 but the only way the store could sells these they marked them down a little more then half price, the sale tag on the stock table and the kit was $ 4.95 with a steal of a deal I couldn,t refuse. I bought 4 of them for $ 20.00. the kit was a typical gimic model for that day it was designed and ran on 6 D cell flashlight batteries, opperating a cam gear box that opperated the 5 inch closed mount turrets torpedo tubes and the twin screws. Also in the kit you a choice of courses that could be set if desired useing a cam that worked off the gear box. 10 years ago I scuttled the gearbox and modernized it with up to date RC she runs on a 6 volt dumas electric motor with a gear reduxction turning two screws and speed control Boats

Ahoy
Here is my RC powered 1/96 scale U.S.S. ARIZONA made from Original copys of the builder plans. I modled her in the measure of 5d. She is powered by 1 dumas 12 volt super panther electric motor driveing 4 screws, Boats

Now finished off cockpit and rear structure and recruited a couple of crew from bargain 4 for ÂA£1.50 Army pack! They are a bit on the small size or it could be a large RIB!
Chris

Here are my latest pics of a trimar frigate that I am building. it is totally scratch built with twim screws powered by two 540 motors and twim escs. The radar antenna, nav lights and turret all turn and work

A Few Pics of my 1/16th Fireboat now fitted with working Fire Monitors (superbly and very kindly produced by PeterHS93)
Ready for testing ASAP - Now I need some 1/16th Crew!

Chris

Just a few more pics, this time of the 1/24th Scale Deans Marine kit I used to scale up the superstructure dimensions for the restoration of my fathers 1/16th scale ST below. Again although built some 2 years ago this was it's first outing on a lake, once more at Crealy near Exeter.
Both 441 & 1515 operated out of Lyme Regis in WW2, 441 on record of rescuing the complete crew of a downed Flying Fortress and 1515 picking up 26 paratroops from Lyme Bay on D day.