Scratched built prototype 1880s victorian tug (hull) by Metcalf Mouldings H.M.S kit length 44" beam 10".

The original tug was built to tow sailing ships in shallows, hence it's shallow draught and wide beam. Well that's my story and I'm sticking to it!!

Another one not finished!

W165 was built by Roger Forlines, he's a member of Shelton Scale Ship Modelers R/C boat club.

This boat took six months to build and is to Scale as laid down by model manufacture, the boat was weathered to depict a long voyage on the north seas.

Also, the Jim Wilder tug, this took four months to build and has been built to look like a turn of the century steam tug which worked the San Fransisco bay area.

The last picture it is dressed up for Christmas.

This is BG Coulies built by Geoff Lewis. its a French Harbour tug that he built following an article in a well know magazine, advertising a set of plans, thanks to the office photocopier he saved himself several quid.

Coullies is driven by 2 550 motors driving Graupner scothell drives (not yet independantly controlled). 12v 4ah Gell battery and some roofing lead makes up the balast.

The frames are 3mm MDF with a balsa and ply skin built to 1/32 scale, the figure sat on the anchor winch used to be a German infrantry man. He recently obtained some Beccs transfers to add some more finishing touches including the french flag.

What does Coullies mean? (pronounced cooee) find a dictionary...

I rescued my PT Boat from EBAY in August 2005. it was owned by a young boy in Birmingham whose Dad had built if for him. it is an original Aerokits kit Fast Patrol Boat. When I bought the boat it had a sound hull with a few damaged fittings, which I removed. Since then I have made new guns, extended the front cabin to carry the life raft to make it look like a late World War II Elco PT Boat and added other new fittings.

I have made 6 working exhausts in brass tubing, have fitted a new open prop shaft running an Octura race prop and a Merco 61 glow engine. it still needs torpedos, guard rails around the machine gun turrets and a few other fittings. The number 349 is from an original Pacific Theatre 80' Elco PT Boat whose name in Bee Bee, which I hope to add at a later date.

I have also painted it in an original Pacific Theatre camouflage from a PT Boat book which I bought for reference and to make it look like a standoff scale model. This boat was also photographed by the local Burton Upon Trent newspaper at the Fireboat day in September 2006. I ran this boat at the Burton Model Boat Club's Fireboat day in September 2006 briefly until I broke the exhaust manifold and had to retire it early.

Kit Yamato which is motorised by Tamiya and is about 2 years old.

It took six months to build and convert to R.C. power for NiCad batteries.

Z15 "Erich Steinbrink"

A german WW2 Destroyer was a Ted Radestock Semi-Kit.

She took just over 2 yrs to build in total, but did include a house move in between!!

She is built as per the kit with the exception of James Lane guardrails and modified Deans funnels as the original resin funnels were very heavy.

She is powered by 2 Deans motors, 35mm props and the batteries are 2 x 7.2 volt 2 Ah NiCad packs.

This model is a British "Hunt" Class destroyer.

It is a Sirmar limited edition (100) semI kit at 1/48 scale and some 6 feet in length. When he bought the model it was already constructed, but as a static model. So out came the jigsaw, Manual NOT powered.

The deck around the aft gun turret was cut to allow a good inspection of the inside of the hull. He tried to remove the bridge superstructure but this would have meant destroying it to remove. Out came the jigsaw again and cut an access hatch in the main deck.

The steering servo was fitted and attached ( by keyhole surgery ) and 2 x MFA 800 motors were fitted. Scale Prop Shop Props were fitted and the radio gear just jury rigged for her first trial. She was roughly ballasted with 2 x 12volt 7Ah batteries and she was ready for her first trials.

She sailed well with no water ingress to the hull, so the radio gear was installed properly with individual speed controllers to each motor. The results are as seen here.

This is the Hugh William Viscount Gough. She is a solent class lifeboat. She went into service in 1963 as the Stornoway lifeboat. She was there for around twenty years.

She then went on to Barra and ended her service at Dunbar. She was sold in 1993 and is now out in Malaysia.

I have scratch built her from the hull up. She has a fibre glass hull and the super structure is made from plasticard. She took four weeks to build. I have some bits and bobs to do to her.

She runs on two MFA 850 torprdos, but I am going to down size to 800's.

We sail her at Mote park Maidstone most Sundays and also at shows.

She is 48" long with a scale of 1:12

This lifeboat was a part-kit from Metcalfe Mouldings, being just a bare hull and superstructure. All the detailed work was scratch- built by my son and I did all the drive and electrics.

It is powered by two 540 motors through a single water-cooled speed controller and the props are about 35mm. My son and I sail it at our club water at Knightcote in Warwickshire. it is now about 4 years old and, (touch wood), pretty reliable.

Rother Class kit built by Barry Sullivan. This has only just been finished and has not been on it's maiden yet.

Also the Trent model, this kit was built about two years ago.

This is my ** version of the Sea Queen. My father owns one of the originals and when one lunch time I saw one on the ** web site I knew I had to get one.
It was to be a winter build project and work started in the autumn of 2006 and it was launched in May 2007. I was very disappointed to see the all white paint finish used on the ** advertisements and decided I was going to re-create the look of the original. Cosmetically the big problem was that the original used mahogany finish ply for the cabin sides and the ** version was just plain birch. However after a bit of staining I was quite happy with the finished colour. This was contrasted against clear coated lime wood deck planking.
Also ***a€™s bag of fittings missed out on the signature life belts so I had to make my own.

One Improvement that I did make was the inclusion of a dashboard, instrument panel and throttle slide.

The graphic on the transom was a custom cut from callie-graphics.

The supplied motor was replaced with an MFA Torpedo 850 which is a direct replacement. ( Same mount, same screw fixing centres etc ).
Battery is a 12V 7A gel cell, ESC is an Mtronics Marine Viper 40A

The first picture here is the aerokits Solent Lifeboat.

The next picture is an aerokits Patrol Torpedo boat.